IEC_62561-2_Ed._1.pdf

Registered trademark of the International Electrotechnical Commission 81/417/FDIS FINAL DRAFT INTERNATIONAL STANDARD PROJET FINAL DE NORME INTERNATIONALE Project number Numro de projet IEC 62561-2 Ed.1 IEC/TC or SC CEI/CE ou SC 81 Secretariat/Secrtariat Italy Submitted for parallel voting in CENELEC Soumis au vote parallle au CENELEC Distributed on/Diffus le 2011-11-25 Voting terminates on/Vote clos le 2012-01-27 Also of interest to the following committees Intresse galement les comits suivants SC 37A,TC 64,TC 77 Supersedes document Remplace le document 81/386/CDV 81/402/RVC Horizontal standard Norme horizontale Other TC/SCs are requested to indicate their interest,if any,in this FDIS to the TC/SC secretary Les autres CE/SC sont requis dindiquer leur intrt,si ncessaire,dans ce FDIS lintention du secrtaire du CE/SC Functions concerned Fonctions concernes Safety Scurit EMC CEM Environment Environnement Quality assurance Assurance de la qualit CE DOCUMENT EST UN PROJET DIFFUS POUR APPROBATION.IL NE PEUT TRE CIT COMME NORME INTERNATIONALE AVANT SA PUBLICATION EN TANT QUE TELLE.OUTRE LE FAIT DTRE EXAMINS POUR TABLIR SILS SONT ACCEPTABLES DES FINS INDUSTRIELLES,TECHNOLOGIQUES ET COMMERCIALES,AINSI QUE DU POINT DE VUE DES UTILISATEURS,LES PROJETS FINAUX DE NORMES INTERNATIONALES DOIVENT PARFOIS TRE EXAMINS EN VUE DE LEUR POSSIBILIT DE DEVENIR DES NORMES POUVANT SERVIR DE RFRENCE DANS LES RGLEMENTATIONS NATIONALES.LES RCIPIENDAIRES DU PRSENT DOCUMENT SONT INVITS PRSENTER,AVEC LEURS OBSERVATIONS,LA NOTIFICATION DES DROITS DE PROPRIT DONT ILS AURAIENT VENTUELLEMENT CONNAISSANCE ET FOURNIR UNE DOCUMENTATION EXPLICATIVE.THIS DOCUMENT IS A DRAFT DISTRIBUTED FOR APPROVAL.IT MAY NOT BE REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL,TECHNOLOGICAL,COMMERCIAL AND USER PURPOSES,FINAL DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.RECIPIENTS OF THIS DOCUMENT ARE INVITED TO SUBMIT,WITH THEIR COMMENTS,NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.Titre Composants des systmes de protection contre la foudre(CSPF)Partie 2:Exigences pour les conducteurs et les lectrodes de terre Title Lightning Protection System Components(LPSC)-Part 2:Requirements for conductors and earth electrodes ATTENTION VOTE PARALLLE CEI CENELEC Lattention des Comits nationaux de la CEI,membres du CENELEC,est attire sur le fait que ce projet finale de Norme internationale est soumis au vote parallle.Les membres du CENELEC sont invits voter via le systme de vote en ligne du CENELEC.ATTENTION IEC CENELEC PARALLEL VOTING The attention of IEC National Committees,members of CENELEC,is drawn to the fact that this final draft International Standard(DIS)is submitted for parallel voting.The CENELEC members are invited to vote through the CENELEC online voting system.Copyright 2011 International Electrotechnical Commission,IEC.All rights reserved.It is permitted to download this electronic file,to make a copy and to print out the content for the sole purpose of preparing National Committee positions.You may not copy or mirror the file or printed version of the document,or any part of it,for any other purpose without permission in writing from IEC.2 62561-2/FDIS IEC(E)CONTENTS FOREWORD.4 INTRODUCTION.6 1 Scope.7 2 Normative references.7 3 Terms and definitions.8 4 Requirements.9 4.1 General.9 4.2 Documentation.9 4.3 Air termination conductors,air termination rods,earth lead-in rods and down conductors.9 4.4 Earth electrodes.11 4.4.1 General.11 4.4.2 Earth rods.11 4.4.3 Joints for earth rods.11 4.4.4 Earth conductors and plates.12 4.5 Marking.12 5 Tests.14 5.1 General conditions for tests.14 5.2 Conductors,air termination rods and earth lead-in rods.15 5.2.1 General.15 5.2.2 Tests for thickness coating on conductors.15 5.2.3 Bend and adhesion test for coated conductors.15 5.2.4 Environmental test.15 5.2.5 Tensile tests.16 5.2.6 Electrical resistivity test.16 5.3 Earth rods.16 5.3.1 General.16 5.3.2 Tests for thickness coating on earth rods.16 5.3.3 Adhesion test.17 5.3.4 Bend test.18 5.3.5 Environmental test.18 5.3.6 Tensile strength tests.19 5.3.7 Test for yield/tensile ratio.19 5.3.8 Electrical resistivity test.20 5.4 Joints for earth rods.20 5.4.1 General.20 5.4.2 Compression tests by mechanical means.20 5.4.3 Environmental Electrical tests.21 5.5 Marking test.22 5.5.1 General conditions for tests.22 5.5.2 Acceptance criteria.22 6 Electromagnetic compatibility(EMC).22 7 Structure and content of the test report.22 7.1 General.22 7.2 Report identification.22 7.3 Specimen description.23 62561-2/FDIS IEC(E)3 7.4 Conductor.23 7.5 Standards and references.23 7.6 Test procedure.23 7.7 Testing equipment,description.23 7.8 Measuring instruments description.23 7.9 Results and parameters recorded.23 7.10 Stat