ISO_IEC_29341-30-12_2017-Character_PDF_documenten.pdf

Information technology UPnP Device Architecture Part 30-12:IoT management and control device control protocol IoT management and control transport generic serviceTechnologies de linformation Architecture de dispositif UPnP Partie 30-12:Protocole de contrle de dispositif de gestion et de contrle de lInternet des objets Service de transport gnrique de gestion et de contrle de lInternet des objetsINTERNATIONAL STANDARDISO/IEC 29341-30-12Reference numberISO/IEC 29341-30-12:2017(E)First edition2017-06 ISO/IEC 2017 ii ISO/IEC 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO/IEC 2017,Published in SwitzerlandAll rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized otherwise in any form or by any means,electronic or mechanical,including photocopying,or posting on the internet or an intranet,without prior written permission.Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh.de Blandonnet 8 CP 401CH-1214 Vernier,Geneva,SwitzerlandTel.+41 22 749 01 11Fax+41 22 749 09 47copyrightiso.orgwww.iso.orgISO/IEC 29341-30-12:2017(E)ISO/IEC 29341-30-12:2017(E)ISO/IEC 2017 All rights reserved iii CONTENTS 1Scope.12Normative References.13Terms,Definitions and Abbreviations.24Notations and conventions.24.1Notation.24.2Data Types.34.3Vendor-defined Extensions.35Service Modelling Definitions.35.1Service Type.35.2SensorTransportGeneric Service Architecture.35.3Key Concepts.35.3.1Sensor Connectivity.35.3.2Sensor HTTP/HTTPS Transport Protocol.45.4State Variables.55.4.1State Variable Overview.55.4.2A_ARG_TYPE_SensorID.55.4.3A_ARG_TYPE_SensorURN.55.4.4A_ARG_TYPE_SensorClientID.55.4.5A_ARG_TYPE_DataRecords.55.4.6A_ARG_TYPE_DataRecordCount.75.4.7A_ARG_TYPE_TransportURL.75.4.8A_ARG_TYPE_SensorDataTypeEnable.75.4.9A_ARG_TYPE_SensorRecordInfo.75.4.10A_ARG_TYPE_TransportConnectionID.85.4.11A_ARG_TYPE_TransportConnections.85.5Actions.95.5.1ConnectSensor().95.5.2DisconnectSensor().125.5.3ReadSensor().135.5.4WriteSensor().145.5.5GetSensorTransportConnections().155.5.6Error Code Summary.166XML Service Description.17 Table 1 State Variables.5Table 2 Actions.9Table 3 Arguments for ConnectSensor().9Table 4 Error Codes for ConnectSensor().11Table 5 Arguments for DisconnectSensor().12Table 6 Error Codes for DisconnectSensor().12Table 7 Arguments for ReadSensor().13Table 8 Error Codes for ReadSensor().14Table 9 Arguments for WriteSensor().14ISO/IEC 29341-30-12:2017(E)iv ISO/IEC 2017 All rights reserved Table 10 Error Codes for WriteSensor().15Table 11 Arguments for GetSensorTransportConnections().16Table 12 Error Codes for GetSensorTransportConnections().16Table 13 Error Code Summary.16 ISO/IEC 29341-30-12:2017(E)ISO/IEC 2017 All rights reserved v Foreword ISO(the International Organization for Standardization)and IEC(the International Electrotechnical Commission)form the specialized system for worldwide standardization.National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity.ISO and IEC technical committees collaborate in fields of mutual interest.Other international organizations,governmental and non-governmental,in liaison with ISO and IEC,also take part in the work.In the field of information technology,ISO and IEC have established a joint technical committee,ISO/IEC JTC 1.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives,Part 1.In particular the different approval criteria needed for the different types of document should be noted.This document was drafted in accordance with the editorial rules of the ISO/IEC Directives,Part 2(see http:/www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO and IEC shall not be held responsible for identifying any or all such patent rights.Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received(see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of Standards,the meaning of the ISO specific terms and expressions related to conformity assessment,as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade(TBT)see the following URL:Foreword Supplementary information ISO/IEC 29341-30-12 was prepared by UPnP Forum and adopted,under the PAS procedure,by joint technical committee ISO/IEC JTC 1,Information technology,in parallel with its approval by national bodies of ISO and IEC.The list of all currently available parts of ISO/IEC 29341 series,under the general