IEC_PAS_61076-3-111-2002.pdf

Connectors for electronic equipment Part 3-111:Detail specification for 8-way,shieldedand unshielded,free and fixed connectors,for industrial environmentsfor frequencies up to 250 MHzP U B L I C L Y A V A I L A B L E S P E C I F I C A T I O NIEC/PAS 61076-3-111Edition 1.02002-06I N T E R N A T I O N A LE L E C T R O T E C H N I C A LC O M M I S S I O NReference number IEC/PAS 61076-3-111Connectors for electronic equipment Part 3-111:Detail specification for 8-way,shieldedand unshielded,free and fixed connectors,for industrial environmentsfor frequencies up to 250 MHzP U B L I C L Y A V A I L A B L E S P E C I F I C A T I O NIEC/PAS 61076-3-111Edition 1.02002-06I N T E R N A T I O N A LE L E C T R O T E C H N I C A LC O M M I S S I O NReference number IEC/PAS 61076-3-111 2 Copyright 2002,IECCONTENTSPageFOREWORD.51Scope.61.1Normative references.62IEC type designation.82.1Terminology.93Common Features.94Industrial RJ45 Variants.94.1General.94.1.1Contact arrangement of all connector types.94.1.2Terminations.94.2Industrial RJ45 Variant 01.104.2.1Industrial RJ45 Variant 01,Fixed Connector.104.2.2Industrial RJ45 Variant 01,Free Connector.114.3Industrial RJ45 Variant 02.124.3.1Industrial RJ45 Variant 02,Fixed Connector.124.3.2Industrial RJ45 Variant 02,Plug Connector.144.4Industrial RJ45 Variant 03.164.4.1Industrial RJ45 Variant 03,Fixed Connector Side.164.4.2Industrial RJ45 Variant 03,Free Connector.175Mounting Information for Variants 01-03.185.1Mounting Information for Variant 01,Fixed Connector.185.2Mounting Information for Variant 02,Fixed Connector.185.3Mounting Information for Variant 03,Fixed Connector.186Gauges.196.1Fixed connectors,RJ 45 Interface.197Characteristics.197.1Climatic category:40/085/21.197.2Electrical.197.2.1Creepage and clearance distances.197.2.2Voltage proof.207.2.3Current-carrying capacity.207.2.4Initial contact resistance.207.2.5Initial insulation resistance.207.3Mechanical.217.3.1Mechanical operation.217.3.2Effectiveness of connector coupling devices.218Test schedule.218.1General.218.2Test Procedures and Measuring Methods.21Copyright 2002,IEC 3 8.3Preconditioning.228.4Wiring and Mounting of Specimens.228.4.1Wiring.228.4.2Mounting.228.5Test Schedules.228.6Arrangement for contact resistance test:.228.7Arrangement for dynamic stress tests(test phase AP2).238.7.1Basic(Minimum)Test Schedule.248.7.2Full Test Schedule.24AnnexesAGauging requirements.29BLocking device mechanical operation Test procedure and requirements.30CGauging continuity procedure.31 4 Copyright 2002,IECINTERNATIONAL ELECTROTECHNICAL COMMISSION_CONNECTORS FOR ELECTRONIC EQUIPMENT Part 3-111:Detail specification for 8-way,shielded and unshielded,free and fixed connectors,for industrial environmentsfor frequencies up to 250 MHzFOREWORDA PAS is a technical specification not fulfilling the requirements for a standard,but made available to thepublic.IEC-PAS 61076-3-111 has been processed by subcommittee 48B:Connectors,of IEC technical committee 48:Electromechanical components and mechanical structures for electronic equipment.The text of this PAS is based on thefollowing document:This PAS was approved forpublication by the P-members of thecommittee concerned as indicated inthe following document:Draft PASReport on voting48B/1174/PAS48B/1219A/RVDFollowing publication of this PAS,the technical committee or subcommittee concerned will investigate thepossibility of transforming the PAS into an International Standard.1)The IEC(International Electrotechnical Commission)is a worldwide organization for standardization comprising allnational electrotechnical committees(IEC National Committees).The object of the IEC is to promote internationalco-operation on all questions concerning standardization in the electrical and electronic fields.To this end and inaddition to other activities,the IEC publishes International Standards.Their preparation is entrusted to technicalcommittees;any IEC National Committee interested in the subject dealt with may participate in this preparatorywork.International,governmental and non-governmental organizations liaising with the IEC also participate in thispreparation.The IEC collaborates closely with the International Organization for Standardization(ISO)inaccordance with conditions determined by agreement between the two organizations.2)The formal decisions or agreements of the IEC on technical matters express,as nearly as possible,an internationalconsensus of opinion on the relevant subjects since each technical committee has representation from allinterested National Committees.3)The documents produced have the form of recommendations for international use and are published in the form ofstandards,technical specifications,technical reports or guides and they are accepted by the National Committeesin that sense.4)In order to promote international unification,IEC National Committees undertake to apply IEC InternationalStandards transparently to the maximum extent possible in their national and regional stand