ISO_IEC_29341-12-10_2015-Character_PDF_documenten.pdf

Information technology UPnP Device Architecture Part 12-10:Remote User Interface Device Control Protocol Remote User Interface Client ServiceTechnologies de linformation Architecture de dispositif UPnP Partie 12-10:Protocole de contrle de dispositif dinterface utilisateur distance Service client dinterface utilisateur distanceINTERNATIONAL STANDARDISO/IEC 29341-12-10Reference numberISO/IEC 29341-12-10:2015(E)Second edition2015-06-15 ISO/IEC 2015 ii ISO/IEC 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized otherwise in any form or by any means,electronic or mechanical,including photocopying,or posting on the internet or an intranet,without prior written permission.Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel.+41 22 749 01 11Fax+41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandISO/IEC 29341-12-10:2015(E)ISO/IEC 29341-12-10:201x(E)ISO/IEC 2015 All rights reserved iii CONTENTS Foreword.v Introduction.vi 1.Scope.12.Normative References.13.Service Modeling Definitions.23.1.ServiceType.2 3.2.State Variables.2 3.2.1.CompatibleUIsUpdateIDEvent.2 3.2.2.CurrentConnections.2 3.2.3.CurrentConnectionsEvent.3 3.2.4.DeviceProfile.3 3.2.5.A_ARG_TYPE_CompatibleUIs.3 3.2.6.A_ARG_TYPE_DisplayMessageType.3 3.2.7.A_ARG_TYPE_InputDataType.3 3.2.8.A_ARG_TYPE_Int.4 3.2.9.A_ARG_TYPE_String.4 3.3.Eventing and Moderation.4 3.3.1.Relationships Between State Variables.4 3.4.Actions.5 3.4.1.Connect.5 3.4.2.Disconnect.6 3.4.3.GetCurrentConnections.7 3.4.4.GetDeviceProfile.8 3.4.5.GetUIListing.9 3.4.6.AddUIListing.9 3.4.7.RemoveUIListing.10 3.4.8.DisplayMessage.11 3.4.9.ProcessInput.12 3.4.10.Non-Standard Actions Implemented by a UPnP Vendor.13 3.4.11.Relationships Between Actions.13 3.4.12.Common Error Codes.14 4.Theory of Operation.154.1.Example Values of State Variables.15 4.1.1.A_ARG_TYPE_URI.15 4.1.2.CurrentConnections.16 4.1.3.A_ARG_TYPE_CompatibleUIs.16 4.1.4.DeviceProfile.17 4.2.Remote UI Scenarios for the Basic DCP.18 4.2.1.Connect,Disconnect and GetCurrentConnections.18 4.2.2.Add,Get and Remove UI Listings.18 4.2.3.Display Message.18 4.2.4.Process Input.18 4.3.Remote UI Scenarios for the Advanced DCP.19 4.3.1.Mirror.19 4.3.2.Move.19 4.3.3.Reconnect.19 4.4.Types of Client Devices.20 ISO/IEC 29341-12-10:201x(E)iv ISO/IEC 2015-All rights reserved 4.4.1.Autonomous Remote UI Clients.20 4.4.2.Fully Remoted Remote UI Clients.20 5.DeviceProfile XSD Schema.216.A_ARG_TYPE_CompatibleUIs XSD Schema.227.XML Service Description.23LIST OF TABLES Table 1:Service State Variables.2 Table 2:Allowed value list for state variable A_ARG_TYPE_DisplayMessageType.3 Table 3:Allowed value list for state variable A_ARG_TYPE_InputDataType.3 Table 4:Event moderation.4 Table 5:Actions.5 Table 6:Arguments for Connect().5 Table 7:Arguments for Disconnect().6 Table 8:Arguments for GetCurrentConnections().7 Table 9:Arguments for GetDeviceProfile().8 Table 10:Arguments for GetUIListing().9 Table 11:Arguments for AddUIListing().9 Table 12:Arguments for RemoveUIListing().10 Table 13:Arguments for DisplayMessage().11 Table 14.Arguments for ProcessInput().12 Table 15:Common Error Codes.14 ISO/IEC 29341-12-10:201x(E)v Foreword ISO(the International Organization for Standardization)and IEC(the International Electrotechnical Commission)form the specialized system for worldwide standardization.National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity.ISO and IEC technical committees collaborate in fields of mutual interest.Other international organizations,governmental and non-governmental,in liaison with ISO and IEC,also take part in the work.In the field of information technology,ISO and IEC have established a joint technical committee,ISO/IEC JTC 1.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives,Part 1.In particular the different approval criteria needed for the different types of document should be noted.This document was drafted in accordance with the editorial rules of the ISO/IEC Directives,Part 2(see http:/www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO and IEC shall not be held responsible for identifying any or all such patent rights.Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received(see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For