ISO_IEC_TR_19763-9_2015.pdf

Information technology Metamodel framework for interoperability(MFI)Part 9:On demand model selectionTechnologies de linformation Cadre du mtamodle pour linteroprabilit(MFI)Partie 9:Slection de modle la demandeTECHNICAL REPORTISO/IEC TR19763-9First edition2015-10-15Reference numberISO/IEC TR 19763-9:2015(E)ISO/IEC 2015 ii ISO/IEC 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015,Published in SwitzerlandAll rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized otherwise in any form or by any means,electronic or mechanical,including photocopying,or posting on the internet or an intranet,without prior written permission.Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh.de Blandonnet 8 CP 401CH-1214 Vernier,Geneva,SwitzerlandTel.+41 22 749 01 11Fax+41 22 749 09 47copyrightiso.orgwww.iso.orgISO/IEC TR 19763-9:2015(E)iii Contents Foreword.vIntroduction.vi1 Scope.12 References.13 Terms,definitions and abbreviated terms.13.1 Terms and definitions.13.2 Abbreviated terms.24 Preliminaries of ODMS.34.1 Associations in RGPS.34.2 Semantic annotation.55 Framework of ODMS.65.1 Model selection approaches.65.2 General procedure of ODMS.76 Typical model selection cases.86.1 Model selection from goal to service.86.2 Model selection from process to service.9Annex A (informative)Example of on demand model selection.10 ISO/IEC 2015 All rights reserved ISO/IEC TR 19763-9:2015(E)iv Figures Figure 1 Associations in RGPS.4Figure 2 Semantic annotation in RGPS.6Figure 3 General procedure of ODMS represented in BPMN.7Figure 4 Model selection from goal to service.8Figure A.1 Graphical representation of the models to be registered.11Figure A.2 Example of role and goal model registration(Part 1 of 2).12Figure A.2 Example of role and goal model registration(Part 2 of 2).13Figure A.3 Example of process model registration.14Figure A.4 Example of service model registration.15 ISO/IEC TR 19763-9:2015(E)ISO/IEC 2015 All rights reservedv Foreword Part 1:Framework Part 3:Metamodel for ontology registration Part 5:Metamodel for process model registration Part 6:Registry summary Part 7:Metamodel for service model registration Part 8:Metamodel for role and goal model registration Part 9:On demand model selection Technical Report Part 10:Core model and basic mapping Part 12:Metamodel for information model registration Part 13:Metamodel for form design registration ISO/IEC TR 19763-9:2015(E)ISO/IEC 2015 All rights reserved ISO(the International Organization for Standardization)and IEC(the International Electrotechnical Commission)form the specialized system for worldwide standardization.National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity.ISO and IEC technical committees collaborate in fields of mutual interest.Other international organizations,governmental and non-governmental,in liaison with ISO and IEC,also take part in the work.In the field of information technology,ISO and IEC have established a joint technical committee,ISO/IEC JTC 1.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives,Part 1.In particular the different approval criteria needed for the different types of document should be noted.This document was drafted in accordance with the editorial rules of the ISO/IEC Directives,Part 2(see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO and IEC shall not be held responsible for identifying any or all such patent rights.Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received(see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade(TBT),see the following URL:Foreword Supplementary information.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO and IEC shall not be held responsible for identifying any or all such patent rights.ISO/IEC 19763-9 was prepared by Joint Technical Committee ISO/IEC JTC 1,Information Technology,Subcommittee SC 32,Data management and Interchange.ISO/IEC 19763 consists of the following parts,under the general title Information technology Metamodel framework for interoperability(MFI):vi Introduction Industrial consortia have engaged in the standardization of d