ISO_IEC_29362_2008E.pdf

Reference numberISO/IEC 29362:2008(E)ISO/IEC 2008 INTERNATIONAL STANDARD ISO/IEC29362First edition2008-06-15Corrected version2008-10-01Information technology Web Services Interoperability WS-I Attachments Profile Version 1.0 Technologies de linformation Interoprabilit des services du Web Profil des fichiers joints WS-I,version 1.0 ISO/IEC 29362:2008(E)PDF disclaimer This PDF file may contain embedded typefaces.In accordance with Adobes licensing policy,this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.In downloading this file,parties accept therein the responsibility of not infringing Adobes licensing policy.The ISO Central Secretariat accepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file;the PDF-creation parameters were optimized for printing.Every care has been taken to ensure that the file is suitable for use by ISO member bodies.In the unlikely event that a problem relating to it is found,please inform the Central Secretariat at the address given below.COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2008 All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.+41 22 749 01 11 Fax +41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2008 All rights reserved ISO/IEC 29362:2008(E)ISO/IEC 2008 All rights reserved iii Contents Foreword.v 1 Scope and introduction.1 1.1 Scope.1 1.2 Relationship to other Profiles.1 1.3 Notational Conventions.1 1.4 Profile Identification and Versioning.3 2 Profile Conformance.3 2.1 Conformance Requirements.3 2.2 Conformance Targets.4 2.3 Conformance Scope.5 2.4 Claiming Conformance.5 3 Attachments Packaging.6 3.1 Root Part.6 3.2 Encoding of Root Part.7 3.3 Media Type of Message.7 3.4 Messages with No Attachments.7 3.5 Dereferencing Attachments.9 3.6 Carrying Additional SOAP Envelopes.9 3.7 Fault Messages with Attachments.9 3.8 Value-space of Content-Id Header.9 3.9 Ordering of MIME Parts.10 3.10 Position of Root Part.11 3.11 Content-Transfer-Encoding.11 ISO/IEC 29362:2008(E)iv ISO/IEC 2008 All rights reserved 3.12 MIME Boundary String.12 4 Attachments Description.12 4.1 Use of MIME Binding Extension.12 4.2 Unbound portType Element Contents.13 4.3 Referencing Message Parts.13 4.4 Referencing Attachments from the SOAP Envelope.14 4.5 Specifying Root Part.18 4.6 Specifying SOAP Headers in Root Part.19 4.7 MIME Binding Schema Fixes.20 4.8 Specifying Alternate Media Types.20 4.9 WSDL Parts.21 4.10 Ordering of Parts.21 4.11 Sending Fault Messages.22 4.12 Describing Faults.22 4.13 Sending Additional Parts Not Described in WSDL.22 4.14 Conformance of SOAP Messages.22 4.15 Example Attachment Description Using mime:conent.22 4.16 Example Attachment Description Using swaRef.25 Appendix A:Referenced Specifications.27 Appendix B:Extensibility Points.28 Appendix C:Normative References.29 Appendix D:Defined Terms.30 Appendix E:Acknowledgements.31 ISO/IEC 29362:2008(E)ISO/IEC 2008 All rights reserved v Foreword ISO(the International Organization for Standardization)and IEC(the International Electrotechnical Commission)form the specialized system for worldwide standardization.National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity.ISO and IEC technical committees collaborate in fields of mutual interest.Other international organizations,governmental and non-governmental,in liaison with ISO and IEC,also take part in the work.In the field of information technology,ISO and IEC have established a joint technical committee,ISO/IEC JTC 1.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,Part 2.The main task of the joint technical committee is to prepare International Standards.Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting.Publication as an International Standard requires approval by at least 75%of the national bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO and IEC shall not be held responsible for identifying any or all such patent rights.ISO/IEC 29362 was prepared by the Web Services Interoperability Organization(WS-I)and was adopted,under the PAS procedure,by Joint Technical Committee ISO/IEC JTC 1,Information technolog