ISO_IEC_17594_2004E.pdf

Reference numberISO/IEC 17594:2004(E)ISO/IEC 2004 INTERNATIONAL STANDARD ISO/IEC17594First edition2004-07-15Information technology Cases for 120 mm and 80 mm DVD-RAM disks Technologies de linformation Coffrets pour disques DVD-RAM de 120 mm et 80 mm ISO/IEC 17594:2004(E)PDF disclaimer This PDF file may contain embedded typefaces.In accordance with Adobes licensing policy,this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.In downloading this file,parties accept therein the responsibility of not infringing Adobes licensing policy.The ISO Central Secretariat accepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file;the PDF-creation parameters were optimized for printing.Every care has been taken to ensure that the file is suitable for use by ISO member bodies.In the unlikely event that a problem relating to it is found,please inform the Central Secretariat at the address given below.ISO/IEC 2004 All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.+41 22 749 01 11 Fax +41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2004 All rights reserved ISO/IEC 17594:2004(E)ISO/IEC 2004 All rights reserved iii Contents Page Section 1-General.1 1 Scope.1 2 Conformance.1 3 Normative references.2 4 Definitions.2 5 Conventions and notations.2 5.1 Representation of numbers.2 5.2 Names.2 6 General description of the case.2 6.1 General description of the Type 1 case(Figure 1).2 6.2 General description of the Type 2 case(Figure 2).2 6.3 General description of the Type 3 case(Figure 2).3 6.4 General description of the Type 4 case(Figure 3).4 6.5 General description of the Type 5 case(Figure 3).4 6.6 General description of the Type 6 case(Figure 4).5 6.7 General description of the Type 7 case(Figure 5).5 6.8 General description of the Type 8 case(Figure 4).6 6.9 General description of the Type 9 case(Figure 5).6 7 General requirements.7 7.1 Environments.7 7.1.1 Test environment.7 7.1.2 Operating environment.7 7.1.3 Storage environment.8 7.1.4 Transportation.8 7.2 Temperature shock.8 7.3 Safety requirement.8 7.4 Flammability.8 Section 2-Dimensional and mechanical characteristics of the case for 120 mm disks.9 8 Dimensional characteristics.9 8.1 Dimensions of the Type 1 case.9 8.1.1 Overall dimensions(Figure 6).9 8.1.2 Location hole(Figure 6).10 8.1.3 Alignment hole(Figure 6).10 8.1.4 Reference surfaces(Figure 7).11 8.1.5 Insertion slots(Figure 8).11 8.1.6 Detents(Figure 8).12 8.1.7 Gripper slots(Figure 8).12 8.1.8 Write-inhibit hole(Figure 9).13 8.1.9 Sensor holes(Figure 9).13 8.1.10 Sensing areas(Figure 9).14 8.1.11 Spindle and head window(Figure 10).14 8.1.12 Shutter shape(Figure 11).15 8.1.13 Path for shutter opener(Figures 12 and 13).15 8.1.14 Label areas(Figure 14).16 8.1.15 Identification marks for Sides A and B(Figure 15).16 8.2 Dimensions of the Type 2 case.28 8.2.1 Overall dimensions(Figure 16).28 8.2.2 Location hole(Figure 16).29 ISO/IEC 17594:2004(E)iv ISO/IEC 2004 All rights reserved 8.2.3 Alignment hole(Figure 16).29 8.2.4 Reference surfaces(Figure 17).29 8.2.5 Insertion slot(Figure 18).30 8.2.6 Detents(Figure 18).30 8.2.7 Gripper slots(Figure 18).31 8.2.8 Write-inhibit hole(Figure 19).31 8.2.9 Sensor holes(Figure 19).32 8.2.10 Sensing areas(Figure 19).32 8.2.11 Spindle and head window(Figure 20).33 8.2.12 Shutter shape(Figure 21).33 8.2.13 Path for shutter opener(Figure 22 and 23).34 8.2.14 Label areas(Figure 24).35 8.2.15 Identification mark for Side A(Figure 25).35 8.2.16 Opening and opening cover for taking the disk out of the case.35 8.3 Dimensions of the Type 3 case.45 8.3.1 Sensor holes.45 8.3.2 Opening and opening cover for taking the disk out of the case.46 8.4 Dimensions of the Type 4 case.46 8.4.1 Sensor holes.46 8.4.2 Opening and opening cover for taking the disk out of the case.46 8.5 Dimensions of the Type 5 case.47 8.5.1 Sensor holes.47 8.5.2 Opening and opening cover for taking the disk out of the case.47 9 Mechanical characteristics.47 9.1 Material.47 9.2 Mass.47 9.3 Edge distortion.47 9.4 Compliance.47 9.5 Shutter opening force.47 10 Interface between the case used as cartridge and a drive.48 10.1 Capture cylinder(Figure 26).48 10.2 Inner dimensions of the case(Figure 27).49 11 Orientation of the disk in the case.50 11.1 Two-sided disk(Type 2S)in case Types 1,4 and 5.50 11.2 One-sided disk(Type 1S)in case Types 1,2 and 3.50 Section 3-Dimensional and Mechanical characteristics of the case fo