IEC_PAS_62515-2007.pdf

IEC/PAS 62515Edition 1.0 2007-08PUBLICLY AVAILABLE SPECIFICATIONPRE-STANDARD Requirements concerning the interoperability between electromechanical and electrical applications in CAx-systems IEC/PAS 62515:2007(E)LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC,Geneva,Switzerland All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either IEC or IECs member National Committee in the country of the requester.If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,please contact the address below or your local IEC member National Committee for further information.IEC Central Office 3,rue de Varemb CH-1211 Geneva 20 Switzerland Email:inmailiec.ch Web:www.iec.ch About the IEC The International Electrotechnical Commission(IEC)is the leading global organization that prepares and publishes International Standards for all electrical,electronic and related technologies.About IEC publications The technical content of IEC publications is kept under constant review by the IEC.Please make sure that you have the latest edition,a corrigenda or an amendment might have been published.?Catalogue of IEC publications:www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria(reference number,text,technical committee,).It also gives information on projects,withdrawn and replaced publications.?IEC Just Published:www.iec.ch/online_news/justpub Stay up to date on all new IEC publications.Just Published details twice a month all new publications released.Available on-line and also by email.?Electropedia:www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French,with equivalent terms in additional languages.Also known as the International Electrotechnical Vocabulary online.?Customer Service Centre:www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance,please visit the Customer Service Centre FAQ or contact us:Email:csciec.ch Tel.:+41 22 919 02 11 Fax:+41 22 919 03 00 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.IEC/PAS 62515Edition 1.0 2007-08PUBLICLY AVAILABLE SPECIFICATIONPRE-STANDARD Requirements concerning the interoperability between electromechanical and electrical applications in CAx-systems INTERNATIONAL ELECTROTECHNICAL COMMISSION VICS 35.240.10 PRICE CODEISBN 2-8318-0000-0 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.2 PAS 62515 IEC:2007(E)CONTENTS FOREWORD.4 INTRODUCTION.5 1 Scope.6 2 Normative references.6 3 Terms and definitions.7 4 Identification and classification of objects.9 4.1 Identification of objects.9 4.2 Identification of connect nodes of objects.10 4.3 Classification of connect nodes of objects.11 4.4 Classification of nets.11 5 CAx-applications.12 5.1 Use of units in software applications.12 5.2 General.12 5.3 Coordinate system.12 5.4 Reference point of 2D/3D pictorial presentations.12 5.5 2D/3D routing.12 6 Arrangement drawings.13 6.1 2D projection views.13 6.2 Net and gross dimensions.15 6.3 Level of presentation.15 6.4 Detail drawings.16 6.5 Foot prints.16 6.6 Further required data element types.17 6.7 Presentation levels of(electric)terminal strips within a 2D space.17 7 Modelling of devices/equipment within the 3D space.18 7.1 Product data for(plug)connectors.18 7.2 Net and gross dimensions.18 7.3 Mounting positions.19 7.5 Further definitions.20 7.6 Parametric descriptions of devices within a 3D space.20 7.7 Parametric description of solid primitives according to IEC 61360-4/ISO 10303-42.21 7.7.1 Position and direction.21 7.7.2 Right angular block.21 7.7.3 Right circular cylinder.22 7.7.4 Right circular tube.22 7.7.5 Right circular truncated cone.22 7.7.6 Right circular cone.23 7.7.7 Sphere.23 7.7.8 Torus.23 7.7.9 Right angular wedge.24 7.7.10 Right angular truncated pyramid.24 7.7.11 Right angular pyramid.24 7.7.12 N-edged regular column.25 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.PAS 62515 IEC:2007(E)3 7.7.13 Half sphere.25 7.7.13 Spherical segment.25 8 General product data.26 8.1 Additional data.27 8.2 General data for conductors and cables.27 8.3 General data per connect node.29 8.4 Thermal data.30 8.5 Environmental data.30 9 Requested functionality of an E-CAD layout system.30 9.1 General.30 9.2 General 3D-requirements.32 Figure 1 Definition of projection views based on ISO 128 with indication of reference point.14 Figure 2 Levels of presentat