ISO_IEC_IEEE_24765_2017.pdf

Systems and software engineering VocabularyIngnierie des systmes et du logiciel VocabulaireINTERNATIONAL STANDARDISO/IEC/IEEE24765Reference numberISO/IEC/IEEE 24765:2017(E)Second edition2017-09 ISO/IEC 2017 IEEE 2017 ISO/IEC 2017 All rights reservedii IEEE 2017 All rights reservedISO/IEC/IEEE 24765:2017(E)COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2017,Published in Switzerland IEEE 2017All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from ISO,IEC or IEEE at the respective address below.ISO copyright office Institute of Electrical and Electronics Engineers,IncCh.de Blandonnet 8 CP 401 3 Park Avenue,New YorkCH-1214 Vernier,Geneva,Switzerland NY 10016-5997,USATel.+41 22 749 01 11 Fax+41 22 749 09 47 copyrightiso.org stds.iprieee.orgwww.iso.orgwww.ieee.orgISO/IEC/IEEE 24765:2017(E)iii ISO/IEC 2017 All rights reserved IEEE 2017 All rights reserved Contents Page Foreword.v Introduction.vi 1 Scope.1 1.1 General.1 1.2 Relationship of the print and internet-accessible versions.1 1.3 Vocabulary structure.1 1.4 PMI Glossary provisions.2 2 Normative references.2 3 Terms,definitions,and abbreviated terms.2 Annex A(informative)List of References.513 Bibliography.514 ISO/IEC/IEEE 24765:2017(E)iv ISO/IEC 2017 All rights reserved IEEE 2017 All rights reserved List of Figures Figure 1 Activity group.10 Figure 2 Bathtub curve.42 Figure 3 Block diagram.47 Figure 4 Box Diagram.50 Figure 5 Bubble chart.52 Figure 6 Call graph.56 Figure 7 Case construct.59 Figure 8 Category.60 Figure 9 Data flow diagram.116 Figure 10 Data structure diagram.119 Figure 11 Directed graph.140 Figure 12 Documentation tree.144 Figure 13 Flowchart.185 Figure 14 If-then-else construct.212 Figure 15 Input-process-output chart.225 Figure 16 Modification request.278 Figure 17 Structure chart.440 Figure 18 UNTIL construct.487 Figure 19 Waterfall model.506 Figure 20 Website.507 Figure 21 WHILE construct.508 ISO/IEC/IEEE 24765:2017(E)v ISO/IEC 2017 All rights reserved IEEE 2017 All rights reserved Foreword ISO(the International Organization for Standardization)and IEC(the International Electrotechnical Commission)form the specialized system for worldwide standardization.National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity.ISO and IEC technical committees collaborate in fields of mutual interest.Other international organizations,governmental and nongovernmental,in liaison with ISO and IEC,also take part in the work.In the field of information technology,ISO and IEC have established a joint technical committee,ISO/IEC JTC 1.IEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating Committees of the IEEE Standards Association(IEEESA)Standards Board.The IEEE develops its standards through a consensus development process,approved by the American National Standards Institute,which brings together volunteers representing varied viewpoints and interests to achieve the final product.Volunteers are not necessarily members of the Institute and serve without compensation.While the IEEE administers the process and establishes rules to promote fairness in the consensus development process,the IEEE does not independently evaluate,test,or verify the accuracy of any of the information contained in its standards.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives,Part 1.In particular the different approval criteria needed for the different types of document should be noted.This document was drafted in accordance with the editorial rules of the ISO/IEC Directives,Part 2(see www.iso.org/directives).Attention is called to the possibility that implementation of this standard may require the use of subject matter covered by patent rights.By publication of this standard,no position is taken with respect to the existence or validity of any patent rights in connection therewith.ISO/IEEE is not responsible for identifying essential patents or patent claims for which a license may be required,for conducting inquiries into the legal validity or scope of patents or patent claims or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance or a Patent Statement and Licensing Declaration Form,if any,or in any licensing agreements are reasonable or nondiscriminatory.Users of this standard are expressly advised that determination of the validity of any patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Further information may be obtained from ISO or the IEEE Standards Association.Any trade name used in this document is information given