ISO_IEC_17345_2006E.pdf

Reference numberISO/IEC 17345:2006(E)ISO/IEC 2006 INTERNATIONAL STANDARD ISO/IEC17345Second edition2006-12-01Information technology Data Interchange on 130 mm Rewritable and Write Once Read Many Ultra Density Optical(UDO)Disk Cartridges Capacity:30 Gbytes per Cartridge First Generation Technologies de linformation change de donnes sur cartouches de disques de 130 mm de diamtre,pour rcriture et pour“write once read many”,de densit ultra-optique(UDO)Capacit:30 Go par cartouche Premire gnration ISO/IEC 17345:2006(E)PDF disclaimer This PDF file may contain embedded typefaces.In accordance with Adobes licensing policy,this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.In downloading this file,parties accept therein the responsibility of not infringing Adobes licensing policy.The ISO Central Secretariat accepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file;the PDF-creation parameters were optimized for printing.Every care has been taken to ensure that the file is suitable for use by ISO member bodies.In the unlikely event that a problem relating to it is found,please inform the Central Secretariat at the address given below.ISO/IEC 2006 All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.+41 22 749 01 11 Fax +41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2006 All rights reserved ISO/IEC 17345:2006(E)ISO/IEC 2006 All rights reserved iiiContents Page Foreword.vii Introduction.viii Section 1 General.1 1 Scope.1 2 Conformance.2 2.1 Optical disk.2 2.2 Generating system.2 2.3 Receiving system.2 2.4 Compatibility statement.2 3 Normative references.2 4 Terms and definitions.2 5 Conventions and notations.6 5.1 Representation of numbers.6 5.2 Names.6 6 Acronyms.6 7 General description.7 8 General requirement.8 8.1 Environments.8 8.2 Temperature shock.9 8.3 Safety requirements.9 8.4 Flammability.9 9 Reference Drive.9 9.1 Optical system.9 9.2 Optical beam.10 9.3 Read Channel.11 9.4 Tracking.11 9.5 Rotation of the disk.11 Section 2 Mechanical and physical characteristics.11 10 Dimensional and physical characteristics of the case.11 10.1 General description of the case.11 10.2 Relationship of Sides A and B.11 10.3 Reference axes and case reference planes.12 10.4 Case drawings.12 10.5 Dimensions of the case.12 10.6 Mechanical characteristics.19 10.7 Drop test.20 10.8 Electro-static discharge test.20 11 Dimensional,mechanical,and physical characteristics of the disk.31 11.1 General description of the disk.31 11.2 Reference axis and plane of the disk.32 11.3 Dimensions of the disk.32 11.4 Mechanical characteristics.34 11.5 Optical characteristics.36 12 Interface between cartridge and drive.37 12.1 Clamping method.37 ISO/IEC 17345:2006(E)iv ISO/IEC 2006 All rights reserved 12.2 Clamping force.37 12.3 Capture cylinder.38 12.4 Disk position in operating condition.38 Section 3 Format of information.40 13 Track and Header geometry.40 13.1 Track and Header shape.40 13.2 Wobble groove.41 13.3 Mirror Area.41 13.4 Direction of spiral.41 13.5 Track pitch.41 13.6 Physical Track number.42 14 Track format.43 14.1 Physical Track layout.43 14.2 Physical Block Address(PBA).43 14.3 Sectors with Mirror Area.46 14.4 Radial alignment.47 15 Sector format.47 15.1 Sector layout.47 15.2 IDL,IDG.49 15.3 Blank fields.50 15.4 Quadrature Wobble Marks(QWM).50 15.5 Gap.51 15.6 Guard.51 15.7 Verify and Protect(VAP).52 15.8 VFO1,VFO2.52 15.9 Sync.53 15.10 Data field.53 15.11 Postamble(PA).54 15.12 Buffer.54 15.13 Transition Area(TA).55 16 Recording codes.55 16.1 Preformatted Header.55 16.2 Data field.55 17 Formatted Zone.57 17.1 General description of the Formatted Zone.57 17.2 Division of the Formatted Zone.57 17.3 Drive test data patterns.64 17.4 SDI Zones usage.64 17.5 DDS Zones Usage.66 18 Layout of the User Zones.67 18.1 General description of the User Zones.67 18.2 Divisions of the User Zones.67 18.3 User Area.67 18.4 Defect Management Area(DMA).69 18.5 Disk Definition Structure(DDS).71 19 Defect Management in the Rewritable(RW)and Write Once Read Many(WORM)Zones.73 19.1 Initialization of the disk.73 19.2 Certification.73 19.3 Disk not certified.74 19.4 Write procedure.75 19.5 Primary Defect List(PDL)format and content.75 19.6 Secondary Defect List(SDL)format and content.76 Section 4 Characteristics of embossed information.77 20 Embossed information Method of testing.77 20.1 Environment.77 ISO/IEC 17345:2006(E)ISO/IEC 2006 All rights r