ISO_IEC_29341-12-2_2015-Character_PDF_documenten.pdf

Information technology UPnP Device Architecture Part 12-2:Remote User Interface Device Control Protocol Remote User Interface Server DeviceTechnologies de linformation Architecture de dispositif UPnP Partie 12-2:Protocole de contrle de dispositif dinterface utilisateur distance Dispositif serveur dinterface utilisateur distanceINTERNATIONAL STANDARDISO/IEC 29341-12-2Reference numberISO/IEC 29341-12-2:2015(E)Second edition2015-06-15 ISO/IEC 2015 ii ISO/IEC 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized otherwise in any form or by any means,electronic or mechanical,including photocopying,or posting on the internet or an intranet,without prior written permission.Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel.+41 22 749 01 11Fax+41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandISO/IEC 29341-12-2:2015(E)ISO/IEC 29341-12-2:2015(E)ISO/IEC 2015-All rights reserved iii CONTENTS Foreword.iv Introduction.v 1.Scope.12.Device Definitions.22.1.Device Type.2 2.2.Device Model.2 2.2.1.Description of Device Requirements.2 2.2.2.Relationships Between Services.4 2.3.Theory of Operation.4 2.3.1.Secure Remote UI Servers(if DeviceSecurity implemented in Remote UI server device)4 3.XML Device Description.54.Test.6Annex A(normative)Access Control Definitions(if DeviceSecurity service is implemented).7 A.1 Permissions.7 A.2 Profiles.8 A.3 Access Control List(ACL)entry.9 LIST OF TABLES Table 1:RemoteUIServerDevice Service Descriptions.2 Table 2:Device Requirements for stand-alone RemoteUIServerDevice.2 Table 3:Device Requirements for embedded RemoteUIServerDevice.3 Table 4:Defined permissions for RemoteUIServer Service.7 ISO/IEC 29341-12-2:2015(E)iv ISO/IEC 2015-All rights reserved Foreword ISO(the International Organization for Standardization)and IEC(the International Electrotechnical Commission)form the specialized system for worldwide standardization.National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity.ISO and IEC technical committees collaborate in fields of mutual interest.Other international organizations,governmental and non-governmental,in liaison with ISO and IEC,also take part in the work.In the field of information technology,ISO and IEC have established a joint technical committee,ISO/IEC JTC 1.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives,Part 1.In particular the different approval criteria needed for the different types of document should be noted.This document was drafted in accordance with the editorial rules of the ISO/IEC Directives,Part 2(see http:/www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO and IEC shall not be held responsible for identifying any or all such patent rights.Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received(see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of the ISO specific terms and expressions related to conformity assessment,as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade(TBT)see the following URL:Foreword Supplementary information ISO/IEC 29341-12-2 was prepared by UPnP Implementers Corporation and adopted,under the PAS procedure,by joint technical committee ISO/IEC JTC 1.Information technology,in parallel with its approval by national bodies of ISO and IEC.This second edition replaces the first edition(ISO/IEC 29341-12-2:2008),which has been technically revised.The list of all currently available parts of ISO/IEC 29341 series,under the general title Information technology UPnP Device Architecture,can be found on the ISO web site.ISO/IEC 29341-12-2:2015(E)ISO/IEC 2015-All rights reserved v Introduction ISO and IEC draw attention to the fact that it is claimed that compliance with this document may involve the use of patents as indicated below.ISO and IEC take no position concerning the evidence,validity and scope of these patent rights.The holders of-these patent rights have assured ISO and IEC that they are willing to negotiate licenses under reasonable and non-discriminatory terms and conditions with applicants throughout the world.In this respect,the statements of the holders of these patent rights are registered with ISO and IEC.Intel Corporation has informed ISO a