ISO_IEC_7501-3_2005.pdf

Reference numberISO/IEC 7501-3:2005(E)ISO/IEC 2005 INTERNATIONAL STANDARD ISO/IEC7501-3Second edition2005-10-15 Identification cards Machine readable travel documents Part 3:Machine readable official travel documents Cartes didentification Documents de voyage lisibles par machine Partie 3:Documents de voyage officiels lisibles par machine ISO/IEC 7501-3:2005(E)PDF disclaimer This PDF file may contain embedded typefaces.In accordance with Adobes licensing policy,this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.In downloading this file,parties accept therein the responsibility of not infringing Adobes licensing policy.The ISO Central Secretariat accepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file;the PDF-creation parameters were optimized for printing.Every care has been taken to ensure that the file is suitable for use by ISO member bodies.In the unlikely event that a problem relating to it is found,please inform the Central Secretariat at the address given below.ISO/IEC 2005 All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.+41 22 749 01 11 Fax +41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2005 All rights reserved ISO/IEC 7501-3:2005(E)ISO/IEC 2005 All rights reserved iiiForeword ISO(the International Organization for Standardization)and IEC(the International Electrotechnical Commission)form the specialized system for worldwide standardization.National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity.ISO and IEC technical committees collaborate in fields of mutual interest.Other international organizations,governmental and non-governmental,in liaison with ISO and IEC,also take part in the work.In the field of information technology,ISO and IEC have established a joint technical committee,ISO/IEC JTC 1.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,Part 2.The main task of the joint technical committee is to prepare International Standards.Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting.Publication as an International Standard requires approval by at least 75%of the national bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO and IEC shall not be held responsible for identifying any or all such patent rights.ISO/IEC 7501-3 was prepared by Joint Technical Committee ISO/IEC JTC 1,Information technology,Subcommittee SC 17,Cards and personal identification.This second edition cancels and replaces the first edition(ISO/IEC 7501-3:1997),of which it constitutes a minor revision.ISO/IEC 7501 consists of the following parts,under the general title Identification cards Machine readable travel documents:Part 1:Machine readable passport Part 2:Machine readable visa Part 3:Machine readable official travel documents INTERNATIONAL STANDARD ISO/IEC 7501-3:2005(E)ISO/IEC 2005 All rights reserved 1Identification cards Machine readable travel documents Part 3:Machine readable official travel documents This part of ISO/IEC 7501 specifies generic formats and minimum data elements for visual inspection and machine reading of official travel documents in the ID-1 and ID-2 card formats containing standardized,globally interoperable machine readable optical character recognition(OCR)data,which may at the option of Governments,be accepted in lieu of a passport as defined in Annex 9(Chapter 3,paragraph 3.4)to the Convention on International Civil Aviation year 1946(as revised).The edition of the International Civil Aviation Organization(ICAO)Document,i.e.Doc 9303 Part 3 Size-1 and Size-2 Machine Readable Official Travel Documents,Sections III and IV,Technical Specifications,which was adopted as ISO/IEC 7501-3:1997 is now out of date and in the process of being revised.ICAO Doc 9303 Part 3 is maintained by a Technical Advisory Group on Machine Readable Travel Documents(TAG/MRTD).ISO/IEC JTC 1 has provided and continues to provide liaison during the TAG/MRTD meetings on Doc 9303 Part 3.Once the new edition of Doc 9303 Part 3 Size-1 and Size-2 Machine Readable Official Travel Documents is finalized by the TAG/MRTD,ISO/IEC JTC 1 will under