ISO_IEC_18092_2013.pdf

Reference numberISO/IEC 18092:2013(E)ISO/IEC 2013 INTERNATIONAL STANDARD ISO/IEC18092Second edition2013-03-15 Information technology Telecommunications and information exchange between systems Near Field Communication Interface and Protocol(NFCIP-1)Technologies de linformation Tlcommunications et change dinformation entre systmes Communication de champ proche Interface et protocole(NFCIP-1)ISO/IEC 18092:2013(E)COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2013 All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized otherwise in any form or by any means,electronic or mechanical,including photocopying,or posting on the internet or an intranet,without prior written permission.Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.+41 22 749 01 11 Fax +41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2013 All rights reserved ISO/IEC 18092:2013(E)ISO/IEC 2013 All rights reserved iii Contents Page Foreword.vIntroduction.vi1Scope.12Conformance.13Normative references.14Terms and definitions.25Conventions and notations.45.1Representation of numbers.45.2Names.46Abbreviated terms.47General.58RF field.68.1Values.68.2Passive communication Mode.68.3Active communication Mode.68.4External RF field detection.69RF Signal Interface.69.1Bit duration.69.2Active communication mode.79.2.1Requirements for fc/128.79.2.2Requirements for fc/64 and fc/32.79.3Passive communication mode.89.3.1Initiator to Target requirements for fc/128.89.3.2Target to Initiator requirements for fc/128.99.3.3Initiator to Target requirements for fc/64 and fc/32.99.3.4Target to Initiator requirements for fc/64 and fc/32.910General Protocol flow.1011Initialisation.1011.1RF Collision Avoidance.1111.1.1Initial RF Collision Avoidance.1111.1.2Response RF Collision Avoidance.1211.2Passive communication mode.1311.2.1Initialisation and Single Device Detection at fc/128.1311.2.2Initialisation and SDD at fc/64 and fc/32.1311.3Active communication mode.1711.3.1Initialisation at fc/128,fc/64,and fc/32.1711.3.2Active communication mode RF Collision Avoidance.1712Transport Protocol.1812.1Transport Data.1812.2Passive communication mode Activation flow.1812.3Active communication mode Activation flow.1912.4Commands.2212.5Activation of the protocol.2212.5.1Attribute Request and Response Commands.2212.5.2Wakeup Request and Response Commands.2812.5.3Parameter Selection Request and Response Commands.30ISO/IEC 18092:2013(E)iv ISO/IEC 2013 All rights reserved 12.6Data Exchange Protocol.3312.6.1Data Exchange Protocol Request and Response.3312.6.2Response timeout extension.3712.6.3Attention Target present.3712.6.4Protocol operation.3712.6.5Multi Activation.3712.6.6More information(Chaining).3812.7Deactivation of the protocol.3812.7.1Deselect Request and Response command.3912.7.2Release Request and Response commands.40Annex A(normative)CRC calculation.42A.1CRC for Active and Passive communication mode at fc/128.42A.2Example of CRC calculation at fc/128.42A.3CRC for Active and Passive communication mode at fc/64 and fc/32.43A.4Example of CRC calculation at fc/64 and fc/32.43Annex B(informative)SAK.44 ISO/IEC 18092:2013(E)ISO/IEC 2013 All rights reserved v Foreword ISO(the International Organization for Standardization)and IEC(the International Electrotechnical Commission)form the specialized system for worldwide standardization.National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity.ISO and IEC technical committees collaborate in fields of mutual interest.Other international organizations,governmental and non-governmental,in liaison with ISO and IEC,also take part in the work.In the field of information technology,ISO and IEC have established a joint technical committee,ISO/IEC JTC 1.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,Part 2.The main task of the joint technical committee is to prepare International Standards.Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting.Publication as an International Standard requires approval by at least 75%of the national bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO and IEC shall not be held responsible for identifying any or all such patent rights.ISO/IEC 18092 was prepared by Joint Technical Committee ISO/IEC JTC 1,Information technology,Subcommittee SC 6,Telecommunications and information exchange between systems.This second edition cancels and replaces the first edition(ISO/IEC 18092:2004),which has been technically revised.ISO/IEC 18092:2013(E)vi ISO/IEC 2013 A