IEC_61800-7-303-2007.pdf

IEC 61800-7-303Edition 1.0 2007-11INTERNATIONAL STANDARD Adjustable speed electrical power drive systems Part 7-303:Generic interface and use of profiles for power drive systems Mapping of profile type 3 to network technologies IEC 61800-7-303:2007(E)LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC,Geneva,Switzerland All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either IEC or IECs member National Committee in the country of the requester.If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,please contact the address below or your local IEC member National Committee for further information.IEC Central Office 3,rue de Varemb CH-1211 Geneva 20 Switzerland Email:inmailiec.ch Web:www.iec.ch About the IEC The International Electrotechnical Commission(IEC)is the leading global organization that prepares and publishes International Standards for all electrical,electronic and related technologies.About IEC publications The technical content of IEC publications is kept under constant review by the IEC.Please make sure that you have the latest edition,a corrigenda or an amendment might have been published.?Catalogue of IEC publications:www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria(reference number,text,technical committee,).It also gives information on projects,withdrawn and replaced publications.?IEC Just Published:www.iec.ch/online_news/justpub Stay up to date on all new IEC publications.Just Published details twice a month all new publications released.Available on-line and also by email.?Electropedia:www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French,with equivalent terms in additional languages.Also known as the International Electrotechnical Vocabulary online.?Customer Service Centre:www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance,please visit the Customer Service Centre FAQ or contact us:Email:csciec.ch Tel.:+41 22 919 02 11 Fax:+41 22 919 03 00 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.IEC 61800-7-303Edition 1.0 2007-11INTERNATIONAL STANDARD Adjustable speed electrical power drive systems Part 7-303:Generic interface and use of profiles for power drive systems Mapping of profile type 3 to network technologies INTERNATIONAL ELECTROTECHNICAL COMMISSION XDICS 29.200;35.100.05 PRICE CODEISBN 2-8318-9382-8LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.2 61800-7-303 IEC:2007(E)CONTENTS FOREWORD.7 INTRODUCTION.9 1 Scope.12 2 Normative references.12 3 Terms,definitions and abbreviated terms.13 3.1 Terms and definitions.13 3.2 Abbreviated terms.16 4 Mapping to PROFIBUS DP.19 4.1 General.19 4.2 Mapping to PROFIBUS data types.19 4.3 Base Model at PROFIBUS DP.19 4.3.1 Communication Devices.19 4.3.2 Communication Relationship.20 4.3.3 Communication Network.21 4.3.4 Communication Services.22 4.3.5 P-Device Communication Model.24 4.3.6 Base Model State Machine.25 4.3.7 Definition of the CO.26 4.4 Drive Model at PROFIBUS DP.26 4.4.1 P-Device.26 4.4.2 Drive Unit.27 4.5 DO IO Data.27 4.5.1 COs for DO IO Data configuration.27 4.5.2 Standard telegram configuration.28 4.5.3 Cyclic Data exchange between DP-Slaves(DXB).30 4.6 Parameter Access.39 4.6.1 PAP for Parameter Access.39 4.6.2 Definition of the Base Mode Parameter Access mechanism.40 4.7 P-Device Configuration.46 4.7.1 P-Device Configuration on PROFIBUS DP.46 4.7.2 Drive Unit Configuration on PROFIBUS DP.47 4.7.3 Getting the Drive Object ID(DO-ID).49 4.8 Alarm Mechanism.51 4.9 Clock Synchronous Operation.51 4.9.1 Sequence of an isochronous DP cycle.51 4.9.2 Time settings.52 4.9.3 Running-up,cyclic operation.57 4.9.4 Parameterisation,configuring(Set_Prm,GSD).68 4.9.5 Clock cycle generation(Global Control)and clock cycle save.69 4.9.6 Monitoring mechanisms.73 4.10 PROFIBUS DP specific Parameter.75 4.10.1 Overview of the communication interface related parameters.75 4.10.2 Definition of the specific parameters.75 4.11 Specified communication functions for the Application Classes.76 5 Mapping to PROFINET IO.77 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.61800-7-303 IEC:2007(E)3 5.1 General.77 5.2 Mapping to PROFINET IO data types.77 5.3 Base Model at PROFINET IO.77 5.3.1 Communication Devices.77 5.3.2 Communication Relationship.78 5.3.3 Communication Network.79 5.3.4 Communication Servic