IEC_60191-2_amd9-2003.pdf

NORME INTERNATIONALE CEIIEC INTERNATIONAL STANDARD 60191-2AMENDEMENT 9AMENDMENT 92003-11CODE PRIX PRICE CODE Pour prix,voir catalogue en vigueur For price,see current catalogue FAmendement 9 Normalisation mcanique des dispositifs semiconducteurs Partie 2:Dimensions Amendment 9 Mechanical standardization of semiconductor devices Part 2:Dimensions Les feuilles de cet amendement sont insrer dans la Publication 60191-2 The sheets contained in this amendment are to be inserted in Publication 60191-2 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.60191-2 Amend.9 CEI/IEC:2003 INSTRUCTIONS POUR LINSERTION DES NOUVELLES PAGES DANS LA CEI 60191-2 Remplacer la page de titre existante par la nouvelle page de titre.Retirer la page 60191 IEC I existante contenant la prface et la remplacer par la nouvelle page 60191 IEC I contenant la prface lamendment 9(2003).Chapitre I:Ajouter les nouvelles feuilles suivantes:60191 IEC I-167E-a/b/c/d/e INSTRUCTIONS FOR THE INSERTION OF NEW PAGES IN IEC 60191-2 Replace the existing title page with the new title page.Remove the existing page 60191 IEC I containing the preface and insert in its place the new page 60191 IEC I containing the preface to Amendment 9(2003).Chapter I:Add the following new sheets:60191 IEC I-167E-a/b/c/d/e LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.Aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd,lectronique ou mcanique,y compris la photo-copie et les microfilms,sans laccord crit de lditeur.No part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from the publisher.International Electrotechnical Commission,3,rue de Varemb,PO Box 131,CH-1211 Geneva 20,Switzerland Telephone:+41 22 919 02 11 Telefax:+41 22 919 03 00 E-mail:inmailiec.ch Web:www.iec.ch Commission Electrotechnique InternationaleInternational Electrotechnical Commission NORME INTERNATIONALE CEIIEC INTERNATIONAL STANDARD 60191-2Premire ditionFirst edition1966Modifie selon les Complments:Amended in accordance with Supplement:A(1967),B(1969),C(1970),D(1971),E(1974),F(1976),G(1978),H(1978),J(1980),K(1981),L(1982),M(1983),N(1987),P(1988),Q(1990),R(1995),S(1995),T(1995),U(1997),V(1998),W(1999),X(1999),Y(2000),Z(2000)et/and Amendement/Amendment 1(2001),2(2001),3(2001),4(2001),5(2002),6(2002),7(2002),8(2003),9(2003)Normalisation mcanique des dispositifs semiconducteurs Partie 2:Dimensions Mechanical standardization of semiconductor devices Part 2:Dimensions LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.COMMISSION LECTROTECHNIQUE INTERNATIONALE INTERNATIONAL ELECTROTECHNICAL COMMISSION PUBLICATION 191-2 PUBLICATION 191-2 NORMALISATION MCANIQUE DES DISPOSITIFS SEMICONDUCTEURS DEUXIME PARTIE:DIMENSIONS MECHANICAL STANDARDIZATION OF SEMICONDUCTOR DEVICES PART 2:DIMENSIONS SOMMAIRE PRAMBULE PRFACE CONCEPTION DE LA NORMALISATION MCANIQUE.Chapitre 00 VALEURS RECOMMANDES POUR CER-TAINES DIMENSIONS DE DESSINS DE DISPOSITIFS SEMICONDUCTEURS.Chapitre 0 DESSINS DENCOMBREMENTS.Chapitre I TYPES DE DISPOSITIFS SEMICONDUC-TEURS GNRALEMENT MONTS DANS LES BOTIERS DU CHAPITRE I DESSINS DEMBASES.Chapitre II DESSINS DE BOTIERS.Chapitre III DESSINS DE CALIBRES.Chapitre IV TABLEAUX MONTRANT LES ASSOCIA-TIONS ENTRE LES BOTIERS ET LES EMBASES.Chapitre V DESSINS OBSOLTES COMPLMENTS AUX LISTES DE CODES NATIONAUX FIGURANT SUR LES FEUILLES DES NORMES DE LA PUBLICATION 191-2 DE LA CEI SUPPRESSIONS DANS LES LISTES DE CODES NATIONAUX FIGURANT SUR LES FEUILLES DE NORMES DE LA PUBLICATION 191-2 DE LA CEI CONTENTS FOREWORD PREFACE PHILOSOPHY OF MECHANICAL STAN-DARDIZATION.Chapter 00 RECOMMENDED VALUES FOR CERTAIN DIMENSIONS OF DRAWINGS OF SEMI-CONDUCTOR DEVICES.Chapter 0 DEVICE OUTLINE DRAWINGS.Chapter I TYPES OF SEMICONDUCTOR DEVICES GENERALLY MOUNTED IN THE PACKAGES OF CHAPTER I BASE DRAWINGS.Chapter II CASE OUTLINE DRAWINGS.Chapter III GAUGE DRAWINGS.Chapter IV TABLES SHOWING ASSOCIATIONS BE-TWEEN CASE OUTLINES AND BASES.Chapter V OBSOLETE DRAWINGS ADDITIONS TO THE LISTS OF NATIONAL CODES APPEARING ON THE STANDARD SHEETS OF IEC PUBLICATION 191-2 DELETIONS TO THE LISTS OF NATIONAL CODES APPEARING ON THE STANDARD SHEETS OF IEC PUBLICATION 191-2 Publication CEI 191-2 Date:1987 IEC Publication 191-2Date:1987 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.60191-2