IEC_60191-2X-1999.pdf

NORMEINTERNATIONALECEIIECINTERNATIONALSTANDARD60191-2XPremire ditionFirst edition1999-09CODE PRIXPRICE CODEPour prix,voir catalogue en vigueurFor price,see current catalogueNVingt-deuxime complment laPublication 60191-2(1966)Normalisation mcanique des dispositifs semiconducteurs Partie 2:DimensionsTwenty-second supplement to Publication 60191-2(1966)Mechanical standardization of semiconductordevices Part 2:DimensionsLes feuilles de ce complment sont insrer dans laPublication 60191-2The sheets contained in this supplement are to beinserted in Publication 60191-2LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.60191-2X CEI/IEC:1999INSTRUCTIONS POUR LINSERTION DESNOUVELLES PAGES DANS LA CEI 60191-2Remplacer la page de titre existante par lanouvelle page de titre.Retirer la page 60191 IEC I existantecontenant la prface et la remplacer par lanouvelle page 60191 IEC I contenant laprface au vingt-deuxime complment.Retirer les pages 60191-2 IEC I-A et les rem-placer par les nouvelles pages 60191-2 IEC I-A.Chapitre I:Ajouter les nouvelles feuilles suivantes:60191 IEC I-138E-a/b/c60191 IEC I-139E-a/b/c/d/e/f60191 IEC I-140E-a/b/c/d/e/f60191 IEC I-141E-a/b/c/d60191 IEC I-148E-a/b/cINSTRUCTIONS FOR THE INSERTIONOF NEW PAGES IN IEC 60191-2Replace the existing title page with the newtitle page.Remove the existing page 60191 IEC Icontaining the preface and insert in its placethe new page 60191 IEC I containing thepreface to the twenty-second supplement.Remove pages 60191-2 IEC I-A and replacethem by the new pages 60191-2 IEC I-A.Chapter I:Add the following new sheets:60191 IEC I-138E-a/b/c60191 IEC I-139E-a/b/c/d/e/f60191 IEC I-140E-a/b/c/d/e/f60191 IEC I-141E-a/b/c/d60191 IEC I-148E-a/b/cLICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.NORMEINTERNATIONALECEIIECINTERNATIONALSTANDARD60191-2Premire ditionFirst edition1966Modifie selon les Complments:Amended in accordance with Supplement:A(1967),B(1969),C(1970),D(1971),E(1974),F(1976),G(1978),H(1978),J(1980),K(1981),L(1982),M(1983),N(1987),P(1988),Q(1990),R(1995),S(1995),T(1995),U(1997),V(1998),W(1999)et/and X(1999)CEI 1999 Droits de reproduction rservs Copyright-all rights reservedAucune partie de cette publication ne peut tre reproduite niutilise sous quelque forme que ce soit et par aucun procd,lectronique ou mcanique,y compris la photocopie et lesmicrofilms,sans laccord crit de lditeur.No part of this publication may be reproduced or utilizedin any form or by any means,electronic or mechanical,including photocopying and microfilm,without permissionin writing from the publisherBureau central de la Commission Electrotechnique Internationale 3,rue de Varemb Genve SuisseCommission Electrotechnique Internationale International Electrotechnical CommissionVingt-deuxime complment laPublication 60191-2(1966)Normalisation mcanique des dispositifs semiconducteurs Partie 2:DimensionsTwenty-second supplement to Publication 60191-2(1966)Mechanical standardization of semiconductordevices Part 2:DimensionsLICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.COMMISSION LECTROTECHNIQUEINTERNATIONALEINTERNATIONALELECTROTECHNICAL COMMISSIONPUBLICATION 191-2PUBLICATION 191-2NORMALISATION MCANIQUEDES DISPOSITIFS SEMICONDUCTEURSDEUXIME PARTIE:DIMENSIONSMECHANICAL STANDARDIZATIONOF SEMICONDUCTORDEVICESPART 2:DIMENSIONSSOMMAIREPRAMBULEPRFACECONCEPTION DE LA NORMALISATIONMCANIQUE.Chapitre 00VALEURS RECOMMANDES POUR CER-TAINES DIMENSIONS DE DESSINS DE DISPOSITIFS SEMICONDUCTEURS.Chapitre 0DESSINS DENCOMBREMENTS.Chapitre ITYPES DE DISPOSITIFS SEMICONDUC-TEURS GNRALEMENT MONTSDANS LES BOTIERS DU CHAPITRE IDESSINS DEMBASES.Chapitre IIDESSINS DE BOTIERS.Chapitre IIIDESSINS DE CALIBRES.Chapitre IVTABLEAUX MONTRANT LES ASSOCIA-TIONS ENTRE LES BOTIERS ET LESEMBASES.Chapitre VDESSINS OBSOLTESCOMPLMENTS AUX LISTES DE CODESNATIONAUX FIGURANT SUR LESFEUILLES DES NORMES DELA PUBLICATION 191-2 DE LA CEISUPPRESSIONS DANS LES LISTESDE CODES NATIONAUX FIGURANTSUR LES FEUILLES DE NORMES DELA PUBLICATION 191-2 DE LA CEICONTENTSFOREWORDPREFACEPHILOSOPHY OF MECHANICAL STAN-DARDIZATION.Chapter 00RECOMMENDED VALUES FOR CERTAINDIMENSIONS OF DRAWINGS OF SEMI-CONDUCTOR DEVICES.Chapter 0DEVICE OUTLINE DRAWINGS.Chapter ITYPES OF SEMICONDUCTOR DEVICESGENERALLY MOUNTED IN THEPACKAGES OF CHAPTER IBASE DRAWINGS.Chapter IICASE OUTLINE DRAWINGS.Chapter IIIGAUGE DRAWINGS.Chapter IVTABLES SHOWING ASSOCIATIONS BE-TWEEN CASE OUTLINES AND BASES.Chapter VOBSOLETE DRAWINGSADDITIONS TO THE LISTS OFNATIONAL CODES APPEARIN