IEC_60191-2_amd1-2001.pdf

NORMEINTERNATIONALECEIIECINTERNATIONALSTANDARD60191-2AMENDEMENT 1AMENDMENT 12001-03CODE PRIXPRICE CODEPour prix,voir catalogue en vigueurFor price,see current catalogueLAmendment 1Normalisation mcanique des dispositifs semiconducteurs Partie 2:DimensionsAmendment 1Mechanical standardization of semiconductordevices Part 2:DimensionsLes feuilles de cet amendement sont insrer dans laPublication 60191-2The sheets contained in this amendment are to beinserted in Publication 60191-2LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.60191-2 Amend.1 CEI/IEC:2001INSTRUCTIONS POUR LINSERTION DESNOUVELLES PAGES DANS LA CEI 60191-2Remplacer la page de titre existante par lanouvelle page de titre.Retirer la page 60191 IEC I existantecontenant la prface et la remplacer par lanouvelle page 60191 IEC I contenant laprface lamendment 1(2001).Retirer la feuille 191 IEC I-54 et la remplacerpar la nouvelle feuille 60191 IEC I-A54.Chapitre I:Ajouter les nouvelles feuilles suivantes:60191 IEC I-159E-a/b60191 IEC I-160E-a/bINSTRUCTIONS FOR THE INSERTIONOF NEW PAGES IN IEC 60191-2Replace the existing title page with the new titlepage.Remove the existing page 60191 IEC Icontaining the preface and insert in its placethe new page 60191 IEC I containing thepreface to Amendment 1(2001).Remove existing sheet 191IEC I-54 andreplace it by new sheet 60191 IEC I-A54.Chapter I:Add the following new sheets:60191 IEC I-159E-a/b60191 IEC I-160E-a/bLICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.NORMEINTERNATIONALECEIIECINTERNATIONALSTANDARD60191-2Premire ditionFirst edition1966Modifie selon les Complments:Amended in accordance with Supplement:A(1967),B(1969),C(1970),D(1971),E(1974),F(1976),G(1978),H(1978),J(1980),K(1981),L(1982),M(1983),N(1987),P(1988),Q(1990),R(1995),S(1995),T(1995),U(1997),V(1998),W(1999),X(1999),Y(2000),Z(2000)et/and Amendement/Amendment 1(2001)Commission Electrotechnique Internationale International Electrotechnical CommissionNormalisation mcanique des dispositifs semiconducteurs Partie 2:DimensionsMechanical standardization of semiconductordevices Part 2:Dimensions IEC 2001 Droits de reproduction rservs Copyright-all rights reservedAucune partie de cette publication ne peut trereproduite ni utilise sous quelque forme que ce soit etpar aucun procd,lectronique ou mcanique,ycompris la photocopie et les microfilms,sans laccordcrit de lditeur.No part of this publication may be reproduced orutilized in any form or by any means,electronic ormechanical,including photocopying and microfilm,without permission in writing from the publisher.International Electrotechnical Commission3,rue de Varemb Geneva,SwitzerlandTelefax:+41 22 919 0300e-mail:inmailiec.ch IEC web site http:/www.iec.chLICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.COMMISSION LECTROTECHNIQUEINTERNATIONALEINTERNATIONALELECTROTECHNICAL COMMISSIONPUBLICATION 191-2PUBLICATION 191-2NORMALISATION MCANIQUEDES DISPOSITIFS SEMICONDUCTEURSDEUXIME PARTIE:DIMENSIONSMECHANICAL STANDARDIZATIONOF SEMICONDUCTORDEVICESPART 2:DIMENSIONSSOMMAIREPRAMBULEPRFACECONCEPTION DE LA NORMALISATIONMCANIQUE.Chapitre 00VALEURS RECOMMANDES POUR CER-TAINES DIMENSIONS DE DESSINS DE DISPOSITIFS SEMICONDUCTEURS.Chapitre 0DESSINS DENCOMBREMENTS.Chapitre ITYPES DE DISPOSITIFS SEMICONDUC-TEURS GNRALEMENT MONTSDANS LES BOTIERS DU CHAPITRE IDESSINS DEMBASES.Chapitre IIDESSINS DE BOTIERS.Chapitre IIIDESSINS DE CALIBRES.Chapitre IVTABLEAUX MONTRANT LES ASSOCIA-TIONS ENTRE LES BOTIERS ET LESEMBASES.Chapitre VDESSINS OBSOLTESCOMPLMENTS AUX LISTES DE CODESNATIONAUX FIGURANT SUR LESFEUILLES DES NORMES DELA PUBLICATION 191-2 DE LA CEISUPPRESSIONS DANS LES LISTESDE CODES NATIONAUX FIGURANTSUR LES FEUILLES DE NORMES DELA PUBLICATION 191-2 DE LA CEICONTENTSFOREWORDPREFACEPHILOSOPHY OF MECHANICAL STAN-DARDIZATION.Chapter 00RECOMMENDED VALUES FOR CERTAINDIMENSIONS OF DRAWINGS OF SEMI-CONDUCTOR DEVICES.Chapter 0DEVICE OUTLINE DRAWINGS.Chapter ITYPES OF SEMICONDUCTOR DEVICESGENERALLY MOUNTED IN THEPACKAGES OF CHAPTER IBASE DRAWINGS.Chapter IICASE OUTLINE DRAWINGS.Chapter IIIGAUGE DRAWINGS.Chapter IVTABLES SHOWING ASSOCIATIONS BE-TWEEN CASE OUTLINES AND BASES.Chapter VOBSOLETE DRAWINGSADDITIONS TO THE LISTS OFNATIONAL CODES APPEARING ONTHE STANDARD SHEETS OFIEC PUBLICATION 191-2DELETIONS TO THE LISTS OFNATIONAL CODES APPEARING ONTHE STANDARD SHEETS OFIEC PUBLICATION 191-2Publication CEI 191-2Date:1987IEC Publication 191-2Date:1987LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATI