IEC_61169-38-2008.pdf

IEC 61169-38Edition 1.0 2008-11INTERNATIONAL STANDARD Radio-frequency connectors Part 38:Sectional specification Radio frequency coaxial connectors model,slide-in(rack and panel applications)Characteristic impedance 50 (type TMA)50 applications IEC 61169-38:2008(E)LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC,Geneva,Switzerland All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either IEC or IECs member National Committee in the country of the requester.If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,please contact the address below or your local IEC member National Committee for further information.IEC Central Office 3,rue de Varemb CH-1211 Geneva 20 Switzerland Email:inmailiec.ch Web:www.iec.ch About the IEC The International Electrotechnical Commission(IEC)is the leading global organization that prepares and publishes International Standards for all electrical,electronic and related technologies.About IEC publications The technical content of IEC publications is kept under constant review by the IEC.Please make sure that you have the latest edition,a corrigenda or an amendment might have been published.?Catalogue of IEC publications:www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria(reference number,text,technical committee,).It also gives information on projects,withdrawn and replaced publications.?IEC Just Published:www.iec.ch/online_news/justpub Stay up to date on all new IEC publications.Just Published details twice a month all new publications released.Available on-line and also by email.?Electropedia:www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French,with equivalent terms in additional languages.Also known as the International Electrotechnical Vocabulary online.?Customer Service Centre:www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance,please visit the Customer Service Centre FAQ or contact us:Email:csciec.ch Tel.:+41 22 919 02 11 Fax:+41 22 919 03 00 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.IEC 61169-38Edition 1.0 2008-11INTERNATIONAL STANDARD Radio-frequency connectors Part 38:Sectional specification Radio frequency coaxial connectors model,slide-in(rack and panel applications)Characteristic impedance 50 (type TMA)50 applications INTERNATIONAL ELECTROTECHNICAL COMMISSION UICS 33.120.20 PRICE CODEISBN 2-8318-1008-7 Registered trademark of the International Electrotechnical Commission LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.2 61169-38 IEC:2008(E)CONTENTS FOREWORD.4 1 Scope.6 2 Normative references.6 3 Mating face and gauge information.7 3.1 Dimensions General connectors Grade 2.7 3.1.1 Connector with pin centre contact (see Figure 1).7 3.1.2 Connectors with socket-centre contact (see Figure 2).8 3.2 Gauges.9 3.2.1 Connectors with pin-centre contact.9 3.2.2 Connectors with socket-centre contact.10 3.3 Dimensions standard test connectors Grade 0.11 3.3.1 Connector with pin-centre contact(see Figure 5).11 3.3.2 Connector with socket-centre contact(see Figure 6).12 3.4 General requirements for connector mounting in modules and on panels.14 3.4.1 Radial misalignment.14 3.4.2 Axial misalignment.14 4 Quality assessment procedure.15 4.1 General.15 4.2 Rating and characteristics(see Clause 6 of IEC 61169-1/QC220000).15 4.3 Test schedule and inspection requirements.18 4.3.1 Acceptance tests(see Table 8).18 4.3.2 Periodic tests(see Table 9).19 4.4 Procedures.20 4.4.1 Quality conformance inspection.20 4.4.2 Qualification approval and its maintenance.20 5 Instructions for preparation of detail specifications.20 5.1 General.20 5.2 Identification of the detail specification.21 5.3 Identification of the component.21 5.4 Performance.21 5.5 Marking,ordering information and related matters.21 5.6 Selection of tests,test conditions and severities.22 5.7 Blank detail specification pro-forma for type TMA connector.23 Figure 1 Connector with pin-centre contact(for dimensions,see Table 1).7 Figure 2 Connector with socket-centre contact(for dimensions,see Table 2).8 Figure 3 Gauge for outer contact of pin connector(for dimensions,see Table 3).9 Figure 4 Gauge pin for socket-centre contact(for dimensions,see Table 4).10 Figure 5 Standard test connector with pin-centre contact(for dimensions,see Table 5).11 Figure 6 Standard test connector with socket-centre contact(for dimensions,see Table 6).12 F