IEC_61196-1-314-2006.pdf

NORMECEIINTERNATIONALEIECINTERNATIONAL61196-1-314STANDARDPremiere editionFirst edition2006-03Cables coaxiaux de communicationPartie 1-314:Methodes dessai mecanique-Essai de pliageCoaxial communication cables-Part1-314:Mechanical test methodsTest for bendingIEC 2006 Droits de reproduction reserves-Copyright-all rights reservedAucune partie de cette publication ne peut etre reprodulte ni No part of this publication may be reproduced or utilized in anyutilisee sous quelque forme que ce soit et par aucun procde,microfilms,sans Iaccord ecrit de rediteur.the publisher.Intemational Electrotechnical Commission,3.rue de Varembe,PO Box 131,CH-1211 Geneva 20,SwitzerlandTelephone:+41 22 919 02 11 Telefax:+41 22 919 03 00 E-mail:inmailiec.chWeb www iec.chCODE PRIXPRICE CODERMePourprix,voircalogue n vigueurFor price,ses current catalogueNot or61196-1-314IEC:2006-3-CONTENTSFOREWORD.71 Scope.112 Normative references113 Terms and definitions.114 Single bending.114.1 Equipment.114.2 Test sample.114.3 Procedure.134.4 Requirements.134.5 Test report.135 Repeated bending.155.1 Equipment.155.2 Test sample155.3 Procedure155.4 Requirements175.5 Test report176 Flexing.196.1 Equipment.196.2 Test sample.196.3 Procedure.196.4 Requirements.216.5 Test report.217 Flexing endurance.217.1 Equipment.217.2 Test sample.217.3 Procedure.237.4 Requirements.237.5 Test report.238 Cable bending under tension(dynamic test).238.1 Equipment.238.2 Test sample.258.3 Procedure.258.4 Requirements.278.5 Test report.279 Stiffness.299.1 General.299.2 Equipment.299.3 Test sample.319.4 Procedure.319.5 Requirements.339.6 Test report.33uight intemudorual Bectrotechnal Commissoro reproducton or networking permitted without lcense from IHSNot for Rosae61196-1-3141EC:2006-7INTERNATIONAL ELECTROTECHNICAL COMMISSIONCOAXIAL COMMUNICATION CABLESPart 1-314:Mechanical test methodsTest for bendingFOREWORD1)The International Electrotechnical Commission(IEC)is a worldwide organization for standardization comprisingall national electrotechnical committees(IEC National Committees).The object of IEC is to promoteinternational co-operation on all questions concerning standardization in the electrical and electronic fields.Tothis end and in addition to other activities,IEC publishes International Standards,Technical Specifications,Technical Reports,Publicly Available Specifications(PAS)and Guides(hereafter referred to as IECPublication(s).Their preparation is entrusted to technical committees;any IEC National Committee interestedin the subject dealt with may participate in this preparatory work.International,governmental and non-governmental organizations liaising with the IEC also participate in this preparation.IEC collaborates closelywith the International Organization for Standardization(iSO)in accordance with conditions determined byagreement between the two organizations2)The formal decisions or agreements of IEC on technical matters express,as nearly as possible,an internationalconsensus of opinion on the relevant subjects since each technical committee has representation from allinterested IEC National Committees.3)IEC Publications have the form of recommendations for international use and are accepted by IEC NationalCommittees in that sense.While all reasonable efforts are made to ensure that the technical content of IECPublications is accurate,IEC cannot be held responsible for the way in which they are used or for anymisinterpretation by any end user.4)In order to promote international uniformity,IEC National Committees undertake to apply IEC Publicationstransparently to the maximum extent possible in their national and regional publications.Any divergencebetween any IEC Publication and the corresponding national or regional publication shall be clearly indicated inthe latter.5)IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for anyequipment declared to be in conformity with an IEC Publication6)All users should ensure that they have the latest edition of this publication.7)No liability shall attach to IEC or its directors.employees,servants or agents including individual experts andmembers of its technical committees and IEC National Committees for any personal injury,property damage orother damage of any nature whatsoever,whether direct or indirect,or for costs(including legal fees)andexpenses arising out of the publication,use of,or reliance upon,this IEC Publication or any other IECPublications.8)Attention is drawn to the Normative references cited in this publication.Use of the referenced publications isindispensable for the correct application of this publication9)Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject ofpatent rights.IEC shall not be held responsible for identifying any or all such patent rights.International Standard IEC 61196-1-314 has been prepared by subcommittee 46A:Coaxialcables,of IEC technical committee 46:Cables,wires,waveguides,r.f.connectors,r.f.andmicrowave passive components and accessories.The text of this standard is based on the following documents:FDISReport on voting46A/785/FD1S46A/798/RVDFull information on the voting for the approval of this standard can be found in the report onvoting indicated in the above tableThis publication has been drafted in accordance with the ISO/IEC Directives,Part 2No rproduction or networking permd wthout oete tom IHSNot lor Resa