IEC_61000-6-1.pdf

INTERNATIONALSTANDARDIEC61000-6-1First edition1997-07 IEC 1997Copyright-all rights reservedNo part of this publication may be reproduced or utilized in any form or by any means,electronic ormechanical,including photocopying and microfilm,without permission in writing from the publisher.International Electrotechnical Commission 3,rue de Varemb Geneva,SwitzerlandTelefax:+41 22 919 0300Electromagnetic compatibility(EMC)Part 6:Generic standards Section 1:Immunity for residential,commercialand light-industrial environmentsCompatibilit lectromagntique(CEM)Partie 6:Normes gnriques Section 1:Immunit pour les environnements rsidentiels,commerciaux et de lindustrie lgreReference numberIEC 61000-6-1:1997(E)IEC web site http:/www.iec.che-mail:inmailiec.chNumberingAs from the 1st January 1997 all IEC publications are issued with a designation inthe 60000 series.Consolidated publicationsConsolidated versions of some IEC publications including amendments areavailable.For example,edition numbers 1.0,1.1 and 1.2 refer,respectively,to thebase publication,the base publication incorporating amendment 1 and the basepublication incorporating amendments 1 and 2.Validity of this publicationThe technical content of IEC publications is kept under constant review by the IEC,thus ensuring that the content reflects current technology.Information relating to the date of the reconfirmation of the publication is availablein the IEC catalogue.Information on the revision work,the issue of revised editions and amendments maybe obtained from IEC National Committees and from the following IEC sources:IEC BulletinIEC YearbookOn-line access*Catalogue of IEC publicationsPublished yearly with regular updates(On-line access)*Terminology,graphical and letter symbolsFor general terminology,readers are referred to IEC 60050:InternationalElectrotechnical Vocabulary(IEV).For graphical symbols,and letter symbols and signs approved by the IEC forgeneral use,readers are referred to publications IEC 60027:Letter symbols to beused in electrical technology,IEC 60417:Graphical symbols for use on equipment.Index,survey and compilation of the single sheets and IEC 60617:Graphicalsymbols for diagrams.*See web site address on title page.61000-6-1 IEC:1997(E)3 CONTENTSPageFOREWORD.4INTRODUCTION.5Clause1Scope and object.62Normative references.73Definitions.84Description of locations.85Performance criteria.96Conditions during testing.97Product documentation.108Applicability.109Immunity test requirements.10Tables1Immunity Enclosure port.112Immunity Ports for signal lines and control lines.123Immunity DC input and d.c.output power ports.134Immunity Input and output a.c.power ports.145Immunity Functional earth ports.1561000-6-1 IEC:1997(E)4 INTERNATIONAL ELECTROTECHNICAL COMMISSION_ELECTROMAGNETIC COMPATIBILITY(EMC)Part 6:Generic standards Section 1:Immunity for residential,commercialand light-industrial environmentsFOREWORD1)The IEC(International Electrotechnical Commission)is a worldwide organization for standardization comprisingall national electrotechnical committees(IEC National Committees).The object of the IEC is to promoteinternational co-operation on all questions concerning standardization in the electrical and electronic fields.Tothis end and in addition to other activities,the IEC publishes International Standards.Their preparation isentrusted to technical committees;any IEC National Committee interested in the subject dealt with mayparticipate in this preparatory work.International,governmental and non-governmental organizations liaisingwith the IEC also participate in this preparation.The IEC collaborates closely with the International Organizationfor Standardization(ISO)in accordance with conditions determined by agreement between the twoorganizations.2)The formal decisions or agreements of the IEC on technical matters express,as nearly as possible,aninternational consensus of opinion on the relevant subjects since each technical committee has representationfrom all interested National Committees.3)The documents produced have the form of recommendations for international use and are published in the formof standards,technical reports or guides and they are accepted by the National Committees in that sense.4)In order to promote international unification,IEC National Committees undertake to apply IEC InternationalStandards transparently to the maximum extent possible in their national and regional standards.Anydivergence between the IEC Standard and the corresponding national or regional standard shall be clearlyindicated in the latter.5)The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for anyequipment declared to be in conformity with one of its standards.6)Attention is drawn to the possibility that some of the elements of this International Standard may be the subjectof patent rights.The IEC shall not be held responsible for identifying any or all such patent rights.International Standard IEC 61000-6-1 has