DIN_IEC_61850-9-2_E_2006-09.pdf

61850-9-2 IEC:2005(E)2 57/800/CDCONTENTSFOREWORD.4INTRODUCTION.61Scope.72Normative references.73Terms and definitions.94Abbreviations.95Communication stack.105.1Overview of the protocol usage.105.2Client/server services and communication profiles.115.2.1Client/server services.115.2.2A-Profile.125.2.3TCP/IP T-Profile.125.3SV service and communication profile.135.3.1SV mapping overview.135.3.2A-Profile.135.3.3T-Profile.135.4Restrictions.156Mapping of IEC 61850-7-2 and IEC 61850-7-3 Data Attributes.167Mapping of IEC 61850-7-2 classes and services.167.1Classes of SV data sets.167.2Definition of SV data sets.168Mapping of the model for the transmission of sampled values.168.1Overview.168.2Mapping of the multicast sampled value control block class and services.168.2.1Multicast sampled value control block definition.168.2.2MSV Services.198.3Mapping of the unicast sampled value control block class and services.198.3.1Unicast sampled value control block definition.198.3.2USV Services.208.4Mapping of the update of the sampled value buffer.218.5Additional definitions for the transmission of sampled values.218.6Definitions for basic data types.239Conformance.239.1Notation.239.2PICS.239.2.1Profile conformance.239.2.2SV Services.2410Substation Configuration language(SCL).25Annex A(informative)ISO/IEC 8802-3 frame format and ASN.1 basic encoding rules.26A.1 ISO/IEC 8802-3 frame format.26A.2 ASN.1 Basic Encoding Rules(BER).27A.3 Example for an ASN.1 coded APDU frame structure.28Annex B(informative)Process bus architectures.29Annex C(informative)Multicast address selection.3161850-9-2 IEC:2005(E)3 57/800/CDFigure 1 OSI reference model and profiles.10Figure 2-Structure of the tag header.14Figure 3 Concatenation of several ASDUs into one frame.21Figure A.2-Basic encoding rules format.27Figure A.3-Format of the tag octets.27Figure A.4-Example for an ASN.1 coded APDU frame structure.28Figure B.1-Alternative process bus architectures.29Table 1 Service requiring client/server communication profile.11Table 2 Service and protocols for client/server communication A-Profile.12Table 3 Service and Protocols for Peer TCP/IP T-Profile.12Table 4 Service requiring SV communication profile.13Table 5 Service and protocols for SV communication A-Profile.13Table 6 SV T-Profile.13Table 7 Default Virtual LAN IDs and priorities.14Table 8 Assigned Ethertype values.15Table 9 MMS TypeDescription definition for MSVCB MMS structure.17Table 10-DstAddress structure.18Table 11 Mapping of multicast sampled value services.19Table 12 MMS TypeDescription definition for USVCB MMS Structure.19Table 13 Mapping of unicast sampled value services.20Table 14 Encoding for the transmission of the sampled value buffer.22Table 15 Encoding for the basic data types.23Table 16 PICS for A-Profile support.24Table 17 PICS for T-Profile support.24Table 18 SV conformance statement.24Table 19 Definitions for SV SCL.25Table C.1 Recommended multicast addressing example.3161850-9-2 IEC:2005(E)4 57/800/CDINTERNATIONAL ELECTROTECHNICAL COMMISSION_COMMUNICATION NETWORKS AND SYSTEMS IN SUBSTATIONS Part 9-2:Specific Communication Service Mapping(SCSM)Sampled values over ISO/IEC 8802-3FOREWORD1)The International Electrotechnical Commission(IEC)is a worldwide organization for standardization comprisingallnationalelectrotechnicalcommittees(IECNationalCommittees).TheobjectofIECistopromoteinternational co-operation on all questions concerning standardization in the electrical and electronic fields.Tothis end and in addition to other activities,IEC publishes International Standards,Technical Specifications,TechnicalReports,PubliclyAvailableSpecifications(PAS)andGuides(hereafterreferredtoas“IECPublication(s)”).Their preparation is entrusted to technical committees;any IEC National Committee interestedin the subject dealt with may participate in this preparatory work.International,governmental and non-governmental organizations liaising with the IEC also participate in this preparation.IEC collaborates closelywith the International Organization for Standardization(ISO)in accordance with conditions determined byagreement between the two organizations.2)Theformaldecisions oragreementsofIEC ontechnicalmatters express,as nearly as possible,aninternational consensus of opinion on the relevant subjects since each technical committee has representationfrom all interested IEC National Committees.3)IEC Publications have the form of recommendations for international use and are accepted by IEC NationalCommittees in that sense.While all reasonable efforts are made to ensure that the technical content of IECPublications is accurate,IEC cannot be held responsible for the way in which they are used or for anymisinterpretation by any end user.4)In order to promote international uniformity,IEC National Committees undertake to apply IEC Publicationstransparently to the maximum extent possible in their national and regional publications.Any divergencebetween any IEC Publication and the corresponding national or