分享
ASTM_F_2431_-_04_2012.pdf
下载文档

ID:191580

大小:88.04KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_F_2431_ _04_2012
Designation:F243104(Reapproved 2012)Standard Specification forRing Bearing,Inner:For Needle Roller Bearing with ThickOuter Ring1This standard is issued under the fixed designation F2431;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers inner rings for needle rollerbearings having thick outer rings.1.2 The inner rings being specified are intended for use onunhardened shafts in conjunction with the MS51961 needleroller bearings specified in Specification F2246.1.2.1 For needle roller bearings with thin outer rings(Speci-fication F2162,MS17131,MS52141)use inner rings specifiedin Specification F2163.1.3 Inner rings designed to this specification are intendedfor use in applications requiring high radial load with minimalangular shaft misalignment.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This specification contains many of the requirements ofMS51962,which was originally developed by the Departmentof Defense and maintained by the Defense Supply Center inRichmond.The following government activity codes may befound in the Department of Defense,Standardization DirectorySD-1.2Preparing activityCustodiansReview ActivityDLAGS4Army ATAir Force84NavyOSAir Force-992.Referenced Documents2.1 ASTM Standards:3E18 Test Methods for Rockwell Hardness of Metallic Ma-terialsF2162 Specification for Bearing,Roller,Needle:DrawnOuter Ring,Full Complement,Without Inner Ring,Openand Closed End,Standard TypeF2163 Specification for Ring,Bearing,Inner:for NeedleRoller Bearing With Drawn Outer RingF2246 Specification for Bearing,Roller,Needle:ThickOuter Ring With Rollers and Cage2.2 ANSI Standard:4ASMEB46.1 SurfaceTexture(SurfaceRoughness,Waviness,and Lay)2.3 SAE Standards:5SAE J404 Chemical Compositions of SAE Alloy SteelsSAE AMSSTD66 Steel:Chemical Composition and Hard-enability2.4 Military Standard.6MIL-STD-130 Identification Marking of U.S.Military Prop-ertyMIL-STD-197 Packaging of Bearings,Associated Parts andSubassemblies2.5 ABMA Standards:7ABMA 4 Tolerance Definitions and Gauging Practices forBall and Roller BearingsABMA 18.2 Needle Roller Bearings Radial,Inch Design2.6 ISO Standard:4ISO 5593 Rolling BearingsVocabulary1This specification is under the jurisdiction ofASTM Committee F34 on RollingElement Bearings and is the direct responsibility of Subcommittee Automotive/Industrial Bearing.Current edition approved Dec.1,2012.Published January 2013.Originallyapproved in 2004.Last previous edition approved in 2004 as F243104.DOI:10.1520/F2431-04R12.2The Military codes that are listed in SD-1 give the address and phone numbersof the DoD contacts.These are found in the DoDs ASSIST website,http:/assist.daps.dla.mil/online/start/.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.5Available from SAE International(SAE),400 Commonwealth Dr.,Warrendale,PA 15096-0001,http:/www.sae.org.6Available on the DODs ASSIST website,http:/assist.daps.dla.mil/online/start/.7Available from Techstreet,3916 Ranchero Drive,Ann Arbor,MI,48108,http:/.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.Terminology3.1 DefinitionsFor definitions of terms used in thisspecification,refer to ABMA STD 4 and ISO 5593.4.Ordering Information4.1 Whenorderingpartsinaccordancewiththisspecification,specify the following:TABLE 1 Inner Ring DimensionsDashNumberdBore Diameter,in.FOutside Diameter,in.BWidth,in.+0.000,-0.005rRadius,in.(see7.3)MatingBearingMS51961Dash Number(seeSpecificationF2246)Nom.Min.Max.Nom.Min.Max.-1380.37460.3750580.62410.62450.7600.025-1-2120.49960.5000340.74880.74930.7600.040-2-3120.49960.5000340.74880.74931.0100.040-3-4580.62460.6250780.87380.87430.7600.040-5-5340.74960.750010.99880.99930.7600.040-8-613160.81200.812510.99880.99930.7600.040-8-713160.81200.812510.99880.99931.0100.040-9-8780.87450.87501181.12361.12411.0100.040-11-915160.93700.93751181.12361.12411.0100.040-11-1010.99951.00001141.24851.24911.0100.040-14-1110.99951.00001141.24851.24911.2600.040-15-121181.12451.12501381.37351.37411.0100.040-18-131181.12451.12501381.37351.37411.2600.040-19-1413161.18701.18751121.49841.49901.2600.060-22-151141.24951.25001121.49841.49901.0100.060-21-161141.24951.25001121.49841.4

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开