分享
ASTM_F_2167_-_19.pdf
下载文档

ID:191541

大小:850.07KB

页数:15页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_F_2167_ _19
Designation:F216719Standard Consumer Safety Specification forInfant Bouncer Seats1This standard is issued under the fixed designation F2167;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis consumer safety specification is intended to minimize the risk of injury or death associatedwith a childs use of an infant bouncer seat.The specific hazards addressed by this specification areproduct disassembly/collapse,stability,and falls from elevated surfaces.1.Scope1.1 This consumer safety specification covers establishmentof requirements,test methods,and marking requirements topromote safe use of an infant bouncer seat by an occupant anda caregiver.1.2 For purposes of this consumer safety specification,aninfant bouncer seat is a freestanding product intended tosupport an occupant in a reclined position to facilitate bouncingby the occupant,with the aid of a caregiver or by other means.Intended occupants are infants who have not developed theability to sit up unassisted(approximately 0 to 6 months ofage).1.3 This consumer safety specification is intended to mini-mize the risk of injury to an occupant resulting from normaluse and reasonably foreseeable misuse or abuse of an infantbouncer seat.1.4 No infant bouncer seat produced after the approval dateof this consumer safety specification shall,either by label orother means,indicate compliance with this specification unlessit conforms to all requirements contained herein.1.5 This consumer safety specification is not intended toaddress incidents and injuries resulting from the interaction ofother persons with the occupant in an infant bouncer seat or theincidents resulting from abuse or misuse by other children.1.6 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.7 The following precautionary caveat pertains only to thetest method portion,Section 7,of this consumer safety speci-fication:This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory requirements prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D3359 Test Methods for Rating Adhesion by Tape TestF404 Consumer Safety Specification for High ChairsF963 Consumer Safety Specification for Toy SafetyF2050 Consumer Safety Specification for Hand-Held InfantCarriers2.2 Federal Regulations:316 CFR 1303 Ban of Lead-Containing Paint and CertainConsumer Products Bearing Lead-Containing Paint16 CFR 1500.48 Technical Requirements for Determining aSharp Point in Toys or Other Articles Intended for Use byChildren Under Eight Years of Age16 CFR 1500.49 Technical Requirements for Determining aSharp Metal or Glass Edge in Toys or Other ArticlesIntended for Use by Children Under Eight Years of Age16 CFR 1500.50-.51 Test Methods for Simulating Use andAbuse of Toys and Other Articles Intended for Use byChildren1This specification is under the jurisdiction of ASTM Committee F15 onConsumer Products and is the direct responsibility of Subcommittee F15.21 onInfant Carriers,Bouncers and Baby Swings.Current edition approved May 1,2019.Published June 2019.Originallyapproved in 2001.Last previous edition approved in 2017 as F2167 17.DOI:10.1520/F2167-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Code of Federal Regulations,available from U.S.Government Printing Office,732 North Capitol St.,NW,Mail Stop:SDE,Washington DC 20401.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 16 CFR 1501 Method for Identifying Toys and Other Ar-ticles Intended for Use by Children Under Three Years ofAge Which Present Choking,Aspiration or IngestionHazards Because o

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开