ASTM_F_3001_-_14.pdf

Designation:F300114Standard Specification forAdditive Manufacturing Titanium-6 Aluminum-4 VanadiumELI(Extra Low Interstitial)with Powder Bed Fusion1This standard is issued under the fixed designation F3001;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers additively manufacturedtitanium-6aluminum-4vanadium with extra low interstitials(Ti-6Al-4V ELI)components using full-melt powder bedfusion such as electron beam melting and laser melting.Thecomponents produced by these processes are used typically inapplications that require mechanical properties similar tomachined forgings and wrought products.Components manu-factured to this specification are often,but not necessarily,postprocessed via machining,grinding,electrical discharge ma-chining(EDM),polishing,and so forth to achieve desiredsurface finish and critical dimensions.1.2 This specification is intended for the use of purchasersor producers or both of additively manufactured Ti-6Al-4VELI components for defining the requirements and ensuringcomponent properties.1.3 Users are advised to use this specification as a basis forobtaining components that will meet the minimum acceptancerequirements established and revised by consensus of themembers of the committee.1.4 User requirements considered more stringent may bemet by the addition to the purchase order of one or moresupplementary requirements,which may include,but are notlimited to,those listed in S1-S4 and S1-S16 in SpecificationF2924.1.5 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.2.Referenced Documents2.1 ASTM Standards:2B214 Test Method for Sieve Analysis of Metal PowdersB243 Terminology of Powder MetallurgyB600 Guide for Descaling and Cleaning Titanium and Tita-nium Alloy SurfacesB769 Test Method for Shear Testing of Aluminum AlloysD3951 Practice for Commercial PackagingE3 Guide for Preparation of Metallographic SpecimensE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE9 Test Methods of Compression Testing of Metallic Mate-rials at Room TemperatureE11 Specification for Woven Wire Test Sieve Cloth and TestSievesE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE238 Test Method for Pin-Type Bearing Test of MetallicMaterialsE407 Practice for Microetching Metals and AlloysE539 Test Method forAnalysis of TitaniumAlloys by X-RayFluorescence SpectrometryE1409 Test Method for Determination of Oxygen and Nitro-gen in Titanium and Titanium Alloys by Inert Gas FusionE1447 Test Method for Determination of Hydrogen in Tita-nium and Titanium Alloys by Inert Gas Fusion ThermalConductivity/Infrared Detection MethodE1820 Test Method for Measurement of Fracture ToughnessE1941 Test Method for Determination of Carbon in Refrac-tory and Reactive Metals and TheirAlloys by CombustionAnalysisE2371 Test Method for Analysis of Titanium and TitaniumAlloys by Direct Current Plasma and Inductively CoupledPlasma Atomic Emission Spectrometry(Performance-Based Test Methodology)F136 Specification for Wrought Titanium-6Aluminum-4Vanadium ELI(Extra Low Interstitial)Alloy for SurgicalImplant Applications(UNS R56401)F2792 TerminologyforAdditiveManufacturingTechnologies,F2924 Specification for Additive Manufacturing Titanium-6Aluminum-4 Vanadium with Powder Bed Fusion2.2 ISO/ASTM Standards:252915 Specification for Additive Manufacturing File Format(AMF)Version 1.11This specification is under the jurisdiction of ASTM Committee F42 onAdditive Manufacturing Technologies and is the direct responsibility of Subcom-mittee F42.05 on Materials and Processes.Current edition approved Feb.1,2014.Published March 2014.Originallyapproved in 2013.Last previous edition approved in 2013 as F3001-13.DOI:10.1520/F3001-142For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 52921 TerminologyforAdditiveManufacturingCoordinate Systems and Test Methodologies2.3 ASQ Standard:3ASQ C1 Specification of General Requirements for a Qual-ity Program2.4 ISO Standards:4ISO 5832-3 Implants for SurgeryMetallic MaterialsPart3:Wrought Titanium 6-Aluminum 4-Vanadium AlloyThird EditionISO 6892 Metallic MaterialsTensile Testing at AmbientTemperatureISO 9001 Quality Management SystemRequirementsISO 9044 Industrial Woven Wire Cloth Technical Require-ments and TestingISO13485 MedicaldevicesQualitymanagementsystemsRequirements for regulatory purposes2.5 SAE Standards:5AMS 2249 Chemical C