_STP_1278-1996.pdf

STP 1278 Effect of Surface Coatings and Treatments on Wear Shyam Bt,hadur,editor ASTM Publication Code Number(PCN):04-012780-27 ASTM l 100 Barr Harbor Drive West Conshohocken PA 19428-2959 Printed in the U.S.A.Copyright by ASTM Intl(all rights reserved);Sat Dec 26 19:06:30 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Library of Congress Cataloging-in-Publication Data Effect of surface coatings and treatments on wear/Shyam Bahadur,editor.(STP;1278)ASTM publication code number(PCN):04-012780-27.Includes bibliographical references and index.ISBN 0-8031-2036-2 1.Mechanical wear.2.Protective coatings.3.Coating processes.I.Bahadur,Shyam,1934-I1.Series:ASTM special technical publication;1278.TA418.4.E32 1996 620.1 1292-dc20 96-14900 CIP Copyright?9 1996 AMERICAN SOCIETY FOR TESTING AND MATERIALS,West Conshohocken,PA.All rights reserved.This material may not be reproduced or copied,in whole or in part,in any printed,mechanical,electronic,film,or other distribution and storage media,without the written consent of the publisher.Photocopy Rights Authorization to photocopy items for internal,personal,or educational classroom use,or the internal,personal,or educational classroom use of specific clients,is granted by the American Society for Testing and Materials(ASTM)provided that the appropriate fee is paid to the Copyright Clearance Center,222 Rosewood Drive,Danvers,MA 01923,Tel:508-750-8400 online:http:/ Review Policy Each paper published in this volume was evaluated by three peer reviewers.The authors addressed all of the reviewers comments to the satisfaction of both the technical editor(s)and the ASTM Committee on Publications.The quality of the papers in this publication reflects not only the obvious efforts of the authors and the technical editor(s),but also the work of these peer reviewers.The ASTM Committee on Publications acknowledges with appreciation their dedication and contribution to time and effort on behalf of ASTM.Printed in Scranton,PA June 1996 Copyright by ASTM Intl(all rights reserved);Sat Dec 26 19:06:30 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Foreword The symposium on Effect of Surface Coatings and Treatments on Wear was held in Phoenix,Arizona,on 7 December 1994.ASTM Committee G2 on Wear and Erosion sponsored the Symposium.Shyam Bahadur,Iowa State University,presided as symposium chairman and is editor of this publication.Copyright by ASTM Intl(all rights reserved);Sat Dec 26 19:06:30 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Contents Overview Overview of Surface Engineering and Wear-K.G.BUDrNSK Friction and Wear of Self-Lubricating TiN-MoS2 Coatings Produced by Chemical Vapor Deposition-P.J.BLAU,C.S.YUST,Y.W.BAE,+.M.BESMANN,AND W.Y.LEE Laser Surface Melting of Carbide Coatings and Their Tribological Behavior-s.BAHADUR AND C.-N.YANG Low-Amplitude Fretting of Hard Coatings of TiN,Diamond-Like Carbon,and Polycrystalline Diamond-o.VINGSBO,M.VENKATACHALAM,M.SUNDQUIST,AND K.SCHOUTERDEN Friction and Wear Mechanisms on CVD Diamond and PVD TiN Coatings Under Fretting Conditions-H.MOHRBACHER,B.BLANPAIN,AND J.-P.CELIS Absorption of Organic Compounds and Organometallies on Ceramic Substrates for Wear Reduction-P.J.KENNEDY AND V.S.AGARWALA Coating-Substrate Interface Stress Management in Wear Protection of Light Alloy Components-s.RAMALINGAM AND L.ZHENG Nanoindentation and Instrumented Scratching Measurements on Hard Coatings-A.W.RUFF Studies on the Characterization and Tribologieal Behavior of Self-Propagating High-Temperature Synthesis(SHS)Coatings of Chromium Cermet-L.LI AND X.QUNJI 22 35 54 76 94 106 124 147 Copyright by ASTM Intl(all rights reserved);Sat Dec 26 19:06:30 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.STP1278-EB/Jun.1996 Overview There is always an effort to increase the performance of mechanical systems.This has re-sulted in the components of the systems being subjected to higher stresses or aggressive en-vironments and lead to the development of high performance materials.In this succession,ceramic materials have shown a great promise because of their high melting point,strength such as modulus of elasticity and hardness,and inertness to common atmospheres.The main drawback of these materials is the lack of ductility and fracture toughness,and poor thermal conductivity.Thus it is natural to think of the coatings of these materials over metals which compensate these materials for these drawbacks by providing the substrates with good tough-ness and high heat transfer characteristics.While coated systems enable the scientist to tailor the structures for specific applications,they introduce