ASTM_F_2736_-_13e1.pdf

Designation:F2736131Standard Specification for6 to 30 in.(152 To 762 mm)Polypropylene(PP)CorrugatedSingle Wall Pipe And Double Wall Pipe1This standard is issued under the fixed designation F2736;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTE8.7 was editorially corrected in December 2014.1.Scope*1.1 This specification covers requirements and test methodsformaterials,dimensions,workmanship,elongation,brittleness,pipe stiffness,and markings for single wall corru-gated polypropylene(PP)pipe and double wall corrugatedpolypropylene(PP)pipe.It covers nominal sizes 6 in.through30 in.(152 mm through 762 mm).1.2 The corrugated polypropylene pipes governed by thisstandard are intended for use in non-pressure applications forsanitary sewers,storm sewers and drainage pipes.Single wallcorrugated polypropylene pipe shall not be used for sanitarysewer applications.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D256 Test Methods for Determining the Izod PendulumImpact Resistance of PlasticsD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD1238 Test Method for Melt Flow Rates of Thermoplasticsby Extrusion PlastometerD1505 Test Method for Density of Plastics by the Density-Gradient TechniqueD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2990 Test Methods for Tensile,Compressive,and FlexuralCreep and Creep-Rupture of PlasticsD3212 Specification for Joints for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsD3895 Test Method for Oxidative-Induction Time of Poly-olefins by Differential Scanning CalorimetryD4101 Specification for Polypropylene Injection and Extru-sion MaterialsD6992 Test Method for Accelerated Tensile Creep andCreep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped IsothermalMethodF412 Terminology Relating to Plastic Piping SystemsF477 Specification for Elastomeric Seals(Gaskets)for Join-ing Plastic Pipe2.2 American Association of State Highway and transpor-tation Offcials(AASHTO)Standard:3AASHTO LRFD Bridge Design Specifications1This test method is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.26 on OlefinBased Pipe.Current edition approved Nov.1,2013.Published December 2013.Originallyapproved in 2010.Last previous edition approved in 2012 as F2736-12.DOI:10.1520/F273613E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Association of State Highway and TransportationOfficials(AASHTO),444 N.Capitol St.,NW,Suite 249,Washington,DC 2001,http:/www.transportation.org*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.3 Transportation Research Record:3TRR No.2028,“Guidelines for Interpreting AASHTOSpecifications to Design or Evaluate Buried Structureswith Comprehensive Solution Methods,”2007.3.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412 and abbreviations are accordance with Terminol-ogy D1600,unless otherwise specified.3.2 Definitions of Terms Specific to This Standard:3.2.1 double wall pipe,ncorrugated pipe with a coex-truded interior liner.3.2.2 single wall pipe,ncorrugated pipe without an inte-rior liner.3.2.3 waterway wall,nthe pipe wall in single wall pipeand the interior wall in double wall