_STP_1189-1993.pdf

STP 1189 Fracture Mechanics:Twenty-Third Symposium Ravinder Chona,editor ASTM Publication Code Number(PCN)04-011890-30 AsT 1916 Race Street Philadelphia,PA 19103 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:12:57 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.ASTM Publication Code Number(PCN)04-011890-30 ISBN:0-8031-1867-8 ISSN:1040-3094 Copyright?9 1993 AMERICAN SOCIETY FOR TESTING AND MATERIALS,Philadelphia,PA.All rights reserved.This material may not be reproduced or copied,in whole or in part,in any printed,mechanical,electronic,film,or other distribution and storage media,without the written consent of the publisher.Photocopy Rights Authorization to photocopy items for internal or personal use,or the internal or personal use of specific clients,is granted by the AMERICAN SOCIETY FOR TESTING AND MATERIALS for users registered with the Copyright Clearance Center(CCC)Transactional Reporting Service,provided that the base fee of$2.50 per copy,plus$0.50 per page is paid directly to CCC,27 Congress St.,Salem,MA 01970;(508)744-3350.For those organizations that have been granted a photocopy license by CCC,a separate system of payment has been arranged.The fee code for users of the Transactional Reporting Service is 0-8031-1867-8/93$2.50+.50.Peer Review Policy Each paper published in this volume was evaluated by three peer reviewers.The authors addressed all of the reviewers comments to the satisfaction of both the technical editor(s)and the ASTM Committee on Publications.The quality of the papers in this publication reflects not only the obvious efforts of the authors and the technical editor(s),but also the work of these peer reviewers.The ASTM Committee on Publications acknowledges with appreciation their dedication and contribution to time and effort on behalf of ASTM.Printed in Baltimore,MD September 1993 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:12:57 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Foreword The Twenty-Third National Symposium on Fracture Mechanics was held on 18-20 June 1991 in College Station,Texas.ASTM Committee E24 on Fracture Testing was the sponsor.Ravinder Chona,Texas A&M University,presided as symposium chairman and is the editor of this publication.Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:12:57 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Contents Overview 1 JERRY L.SWEDLOW MEMORIAL LECTURE Structural Problems in Search of Fracture Mechanics Solutions-J.M.BARSOM ELASTIC-PLASTIC FRACTURE MECHANICS-ANALYSES AND CONSTRAINT ISSUES Crack Initiation Under Generalized Plane-Strain Conditions-D.g.M.SHUM AND J.G.MERKLE 37 Experimental Relationship Between Equivalent Plastic Strain and Constraint for Crack Initiation-w.G.REUTER,W.R.LLOYD,R.L.WILLIAMSON,J.A.SMITH,AND J.S.EPSTEIN 55 A Comparison of Weibull and/1 Analyses of Transition Range Data-D.E.McCABE 80 Near-Crack-Tip Transverse Strain Effects Estimated with a Large Strain Hollow Cylinder Analogy-J.G.MERKLE 95 The Conditions at Ductile Fracture in Tension Tests-g.J.DEXTER AND S.ROY 115 Developing J-R Curves Without Displacement Measurement Using Normalization-g.LEE AND J.D.LANDES 133 Evaluation of Dynamic Fracture Toughness Using the Normalization Method-R.HERRERA,G.CARCAGNO,AND L.A.DE VEDIA 168 Asymptotic Analysis of Steady-State Crack Extension of Combined Modes I and III in Elastic-Plastic Materials with Linear Hardening-H.YUAN AND A.CORNEC 185 An Asymptotic Analysis of Static and Dynamic Crack Extension Along a Ductile Bimaterial Interface/Anti-Plane Case-H.YUAN AND K.-H.SCHWALSE 208 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:12:57 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.ELASTIC-PLASTIC FRACTURE MECHANICS-APPLICATIONS An Application Methodology for Ductile Fracture Mechanics-J.D.LANDES,Z.ZHOU,AND K.H.BROWN Growth of Surface Cracks During Large Elastic-Plastic Loading Cycles-R.C.McCLUNG,S.J.HUDAK,JR.,M.L.BARTLETT,AND J.H.FITZGERALD Level-3 Crack-Tip Opening Displacement(CTOD)Assessment of Welded Wide Plates in Bending-Effect of Overmarching Weld metal-s.BERGE,O.I.EIDE,AND M.FUJIKUBO Limit Pressure Analysis of a Cylindrical Vessel with Longitudinal Crack-X.CHEN,P.ALBRECHT,AND J.JOYCE A Deep Part-Through All-Around Circumferential Crack in a Cylindrical Vessel Subject to Combined Thermal and Pressure Load-L.CHEN,P.C.PARIS,AND H.TADA Study of a Crack-Tip Region Under Small-Scale Yielding Conditions-C.A.SCIAMMARELLA,A.ALBERTAZZI,JR.,AND J.MOURIKES Fracture Properties of Specially Heat-Treated ASTM A508 Class 2 Pressure Vessel Steei-D.J.ALEXANDER AND R.D.CHEVERTON 229 265 284 310 330 34