分享
ASTM_F_2040_-_18.pdf
下载文档

ID:190589

大小:125.27KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_F_2040_ _18
Designation:F204018An American National StandardStandard Specification forHelmets Used for Recreational Snow Sports1This standard is issued under the fixed designation F2040;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification defines performance requirements forhelmets used in nonmotorized recreational snow sports(suchas skiing,snowboarding,and other alpine sports).This speci-fication is a performance standard and is not intended to restrictdesign.Although a helmet that meets this specification willhelp reduce the risk of some types of injuries to the head atslower speeds,the protection is limited.The user is responsiblefor participating in the sport within his/her abilities and thenature of the snow conditions which may vary widely.Com-pliance with the common sense rules of the sports safety,including any applicable responsibility codes,is essential tohelp reduce the risk of personal injury.1.2 All testing and requirements of this specification shallbe in accordance with Test Methods F1446,except where notedherein.1.3 Partial utilization of this specification is prohibited.Anystatement of compliance with this specification shall be acertification that the product meets all of the requirements ofthe specification in its entirety.A product that fails to meet anyone of the requirements of this specification is considered tohave failed the standard and should not be sold with anyindication that it meets parts of the standard.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2F1446 Test Methods for Equipment and Procedures Used inEvaluating the Performance Characteristics of ProtectiveHeadgear3.Headforms3.1 Headforms to be used in this specification are asspecified in the section on Test Headforms of Test MethodsF1446.The appropriate size headform shall be selected inaccordance with the section on Headform Size Selection ofTest Methods F1446 for the helmet to be tested.4.Anvils and Impact Velocities4.1 Anvils to be used for impact tests in this specificationare described as follows:4.1.1 Flat Anvil,as described in the section on Apparatus ofTest Methods F1446.4.1.2 Hemispherical Anvil,as described in the section onApparatus of Test Methods F1446.4.1.3 Edge Anvil,constructed of solid steel in accordancewith Fig.1.4.2 Impact Velocities:4.2.1 Impacts upon the flat anvil shall achieve a velocity of6.2 m/s(corresponding to a theoretical drop height of 2.0 m).4.2.2 Impacts upon the hemispherical anvil shall achieve avelocity of 4.8 m/s(corresponding to a theoretical drop heightof 1.2 m).4.2.3 Impacts upon the edge anvil shall achieve a velocity of4.5 m/s(corresponding to a theoretical drop height of 1.0 m).4.2.4 The impact velocity shall be measured during the last40 mm of free-fall for each test and shall be within 3%of thevelocities specified in 4.2.1,4.2.2,and 4.2.3.5.Marking the Test Line5.1 The test line is shown in Fig.2 and shall be marked inaccordance with Test Methods F1446.6.Conditioning and Number of Samples6.1 Four sample helmets are required for each shell/linersize combination.6.2 Conditioning of the samples to be tested is described inthe section on Conditioning Environment of Test MethodsF1446,but differs as follows:6.2.1 Low TemperatureThe low temperature shall be 22to 28C.1This specification is under the jurisdiction of ASTM Committee F08 on SportsEquipment,Playing Surfaces,and Facilitiesand is the direct responsibility ofSubcommittee F08.53 on Headgear and Helmets.Current edition approved March 1,2018.Published March 2018.Originallyapproved in 2000.Last previous edition approved in 2011 as F2040 11.DOI:10.1520/F2040-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.2.2 High TemperatureThe high temperature shall be 32to 38C.7.Impact Sites7.1 Centers of impact can

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开