温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_F_1732_
_12
Designation:F173212Standard Specification forPoly(Vinyl Chloride)(PVC)Sewer and Drain Pipe ContainingRecycled PVC Material1This standard is issued under the fixed designation F1732;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers pipe made from PVC com-pound that includes recycled PVC material.This specificationcoversrequirementsandtestmethodsformaterials,dimensions,workmanship,chemical resistance,and joint tight-ness of poly(vinyl chloride)(PVC)sewer and drain pipe.Four-inch perforated pipe is also covered;the joint tightnesstest is not applicable for this product.A form of marking toindicate compliance with this specification is also included.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The text of this standard references notes and footnoteswhich provide explanatory material.These notes,footnotes,and theAppendices(excluding those in tables and figures)shallnot be considered as requirements of this standard.1.4 The following precautionary caveat pertains only to thetest methods portion,Section 7,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2152 Test Method for Adequacy of Fusion of ExtrudedPoly(Vinyl Chloride)(PVC)Pipe and Molded Fittings byAcetone ImmersionD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2564 Specification for Solvent Cements for Poly(VinylChloride)(PVC)Plastic Piping SystemsD2729 Specification for Poly(Vinyl Chloride)(PVC)SewerPipe and FittingsD3034 Specification for Type PSM Poly(Vinyl Chloride)(PVC)Sewer Pipe and FittingsF412 Terminology Relating to Plastic Piping Systems2.2 Federal Standard:Fed.Std.No.123 Marking for Shipment(Civil Agencies)32.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage33.Terminology3.1 DefinitionsDefinitions used are in accordance withTerminology F412,and abbreviations are in accordance withTerminology D1600,unless otherwise specified.The abbrevia-tion for poly(vinyl chloride)is PVC.3.2 Definitions of Terms Specific to This Standard:3.2.1 external recycled materialclean rework materialgenerated by a manufacturer,processor,or fabricator in afacility outside the plant where this pipe(PS 1)is made.3.2.2 internal recycled materialclean rework materialgenerated from the manufacturers own pipe or fitting produc-tion.1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approved Feb.1,2012.Published March 2012.Originallyapproved as PS 1 in 1994.Last previous edition approved in 1996 asF173296(2005).DOI:10.1520/F1732-12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.2.3 post-consumer recycled materialthose plastics com-posed of post-consumer material or recovered material only,orboth,that may or may not have been subjected to additionalprocessing steps of the types used to make products such asrecycled-regrind,or reprocessed or reconstituted plastics.These materials must be clean and graded as to material cellclass.3.2.4 recycled materialsgeneral term that encompasses allthree subgroupsexternal recycled material,internal recycledmaterial,and post-consumer recycled material.NOTE1The terms in 3.2.1 and