ASTM_F_2066_-_13e1.pdf

Designation:F2066131Standard Specification forWrought Titanium-15 Molybdenum Alloy for Surgical ImplantApplications(UNS R58150)1This standard is issued under the fixed designation F2066;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEThe designation was corrected editorially in December 2013.1.Scope*1.1 This specification covers the chemical,mechanical,andmetallurgical requirements for wrought titanium-15 molybde-num alloy to be used in the manufacture of surgical implants(1).21.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of each other.Combiningvalues from the two systems may result in non-conformancewith the standard.2.Referenced Documents2.1 ASTM Standards:3E8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE112 Test Methods for Determining Average Grain SizeE290 Test Methods for Bend Testing of Material for Ductil-ityE539 Test Method forAnalysis of TitaniumAlloys by X-RayFluorescence SpectrometryE1409 Test Method for Determination of Oxygen and Nitro-gen in Titanium and Titanium Alloys by Inert Gas FusionE1447 Test Method for Determination of Hydrogen in Tita-nium and Titanium Alloys by Inert Gas Fusion ThermalConductivity/Infrared Detection MethodE1941 Test Method for Determination of Carbon in Refrac-tory and Reactive Metals and TheirAlloys by CombustionAnalysisE2371 Test Method for Analysis of Titanium and TitaniumAlloys by Direct Current Plasma and Inductively CoupledPlasma Atomic Emission Spectrometry(Performance-Based Test Methodology)F67 Specification for Unalloyed Titanium,for Surgical Im-plant Applications(UNS R50250,UNS R50400,UNSR50550,UNS R50700)F748 Practice for Selecting Generic Biological Test Methodsfor Materials and DevicesF981 Practice for Assessment of Compatibility of Biomate-rials for Surgical Implants with Respect to Effect ofMaterials on Muscle and BoneF1408 Practice for Subcutaneous Screening Test for ImplantMaterialsIEEE/ASTM SI 10 American National Standard for Use ofthe International System of Units(SI):The Modern MetricSystem2.2 Aerospace Material Specifications:4AMS 2249 Chemical Check Analysis Limits,Titanium andTitanium AlloysAMS 2631 Ultrasonic Inspection Titanium and TitaniumAlloy Bar and BilletAMS 2380 Approval and Control of Premium Quality Tita-nium Alloys2.3 ISO Standards:5ISO 6892 Metallic Materials Tensile Testing at AmbientTemperatureISO 9001 Quality Management Systems Requirements2.4 American Society for Quality Standard:ASQ C1 Specification of General Requirements for a Qual-ity Control Program61This specification is under the jurisdiction of ASTM Committee F04 onMedical and Surgical Materials and Devices and is the direct responsibility ofSubcommittee F04.12 on Metallurgical Materials.Current edition approved Oct.1,2013.Published November 2013.Originallyapproved in 2001.Last previous edition approved in 2011 as F2066 11.DOI:10.1520/F206613E01.2The boldface numbers in parentheses refer to the list of references at the end ofthis standard.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from Society of Automotive Engineers(SAE),400 CommonwealthDr.,Warrendale,PA 15096-0001,http:/www.sae.org.5Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.6Available from American Society for Quality(ASQ),600 N.Plankinton Ave.,Milwaukee,WI 53203,http:/www.asq.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 alpha+beta annealed,nthe condition of the mate-rial that is obtained if,following the final hot-working orcold-working operation,the mill product may be rapidlyquenched,for example,by water quenching or pressurizedhelium gas,from a temperature below the beta transus ofapproximately 1382F 750C.3.1.2 alpha+beta annealed+aged,nthe condition of thematerial that is obtained by reheating the alpha+beta annealedmaterial to a time-temperature combination below the betatransus to increase the strength of the alloy.3.1.3 beta annealed,nthe condition of the material that isobtained if,following the final hot-working or cold-workingoperation,the mill product is rapidly quenched,for example,by water quenching or pressu