ASTM_F_599_-_95.pdf

Designation:F 599 95An American National StandardStandard Specification forPoly(Vinylidene Chloride)(PVDC)Plastic-Lined FerrousMetal Pipe and Fittings1This standard is issued under the fixed designation F 599;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers factory-made poly(vinylidenechloride)(PVDC)plastic-lined ferrous metal pipe and fittingsprimarily intended for conveying corrosive liquids and gases.Requirements for materials,workmanship,dimensions,con-struction,working pressure and temperatures,test methods,and markings are included.NOTE1This specification does not include products coated withPVDC nor does it define the suitability of PVDC-lined components inchemical environments.1.2 The values given in parentheses are provided for infor-mation purposes only.1.3 The ferrous piping products shall meet the requirementsof the relevant specifications listed in 1.3.1,1.3.2,and 1.3.3.Nominal sizes from 1 through 8 in.in 125,150,and 300 psiratings are covered.NOTE2The PVDC sealing faces may prevent achievement of the fullpressure rating of the ferrous housing.For pressure limitations,themanufacturer should be consulted.1.3.1 For Ferrous Pipe:Title of SpecificationASTMDesignationPipe,Steel,Black,and Hot-Dipped,Zinc-Coated,Weldedand SeamlessA 53Seamless Carbon Steel Pipe for High-TemperatureServiceA 106Electric-Resistance-Welded-Carbon and Alloy SteelMechanical Tubing.A 513Electric-Resistance-Welded Steel PipeA 135Electric-Welded Low-Carbon Steel Pipe for the ChemicalIndustryA 5871.3.2 For Ferrous Flanges:Title of SpecificationASTMDesignationGray Iron CastingsA 48Forgings,Carbon Steel for Piping ComponentsA 105Gray Iron Castings for Valves,Flanges,and Pipe FittingsA 126Forgings,Carbon Steel for General Purpose PipingA 181Forged or Rolled Alloy-Steel Pipe Flanges,ForgedFittings,and Valves and Parts for High-TemperatureServiceA 182Carbon-Steel Castings Suitable for Fusion Welding forHigh-Temperature ServiceA 216Gray Iron Castings for Pressure-Containing Parts forTemperatures up to 650F(345C)A 278Ferritic Ductile Iron Pressure-Retaining Castings for UseAt Elevated TemperaturesA 395Ductile Iron CastingsA 5361.3.3 For Ferrous Fittings:Title of SpecificationASTMDesignationGray Iron CastingsA 48Forgings,Carbon Steel for Piping ComponentsA 105Gray Iron Castings for Valves,Flanges and Pipe FittingsA 126Forgings,Carbon Steel,for General Purpose PipingA 181Forged or Rolled Alloy-Steel Pipe Flanges,ForgedFittings,and Valves and Parts for High-TemperatureServiceA 182Carbon-Steel Castings Suitable for Fusion Welding forHigh-Temperature ServiceA 216Piping Fittings of Wrought Carbon Steel and Alloy Steel forModerate and Elevated TemperaturesA 234Gray Iron Castings for Pressure-Containing Parts forTemperatures up to 650F(345C)A 278Alloy Steel Castings Specially Heat-Treated for Pressure-Containing Parts Suitable for High-Temperature ServiceA 389Ferritic Ductile Iron Pressure-Retaining Castings for Use atElevated TemperaturesA 395Wrought Austenitic Stainless Steel Piping FittingsA 4031.4 The PVDC-lined pipe and fitting assemblies are limitedto use from 18 to 79C(0 to 175F).For use below 18C(0F)consult the manufacturer.Use in specific aggressiveenvironments may alter the above temperature range.Theoperating temperature range shall be established by mutualagreement between consumer and producer.NOTE3Storage or handling below 7C(20F)of uninstalled 4,6,and 8-in.lined pipe should be avoided.2.Referenced Documents2.1 ASTM Standards:D 729 Specification for Vinylidene Chloride Molding Com-pounds2D 792 Test Methods for Specific Gravity(Relative Density)1This specification is under the jurisdiction ofASTM Committee F-17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.11 onComposite.Current edition approved Sept.10,1995.Published November 1995.Originallypublished as F 599 78.Last previous edition F 599 93.2Annual Book of ASTM Standards,Vol 08.01.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.and Density of Plastics by Displacement2D 1505 Test Method for Density of Plastics by the Density-Gradient Technique2D 1600 Terminology for Abbreviated Terms Relating toPlastics2F 412 Terminology Relating to Plastic Piping Systems32.2ANSI Standards:B 16.1 Cast Iron Pipe Flanges and Flanged Fittings4B 16.5 Steel Pipe Flanges and Flanged Fittings43.Terminology3.1 The terminology used is in accordance with Terminol-ogy F 412,and abbreviations are in accordance with Terminol-ogy D 1600,unless otherwise specified.3.2 The abbreviation for poly(vinylidene chloride)isPVDC.4.Materials4.1 Lining:4.1.1 MaterialThe lining shall be made from PVDCcompounds conforming to the requirements of Specific