_STP_1172-1992.pdf

STP 1172 Chevron-Notch Fracture Test Experience:Metals and Non-Metals Kevin R.Brown and Francis I.Baratta,editors ASTM Publication Code Number(PCN)04-011720-30 AsTM 1916 Race Street Philadelphia,PA 19103 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:08:26 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Library of Congress Cataloging-in-Publication Data Chevron-notch fracture test experience-metals and non-metals/Kevin R.Brown and Francis I.Baratta,editors.p.cm.-(STP;1172)Contains papers presented at the symposium held in Indianapolis,May 6,1991,and sponsored by ASTM Committee E-24 on Fracture Testing.ASTM publication code number(PCN)04-011720-30.Includes bibliographical references and indexes.ISBN 0-8031-1480-X 1,Fracture mechanics-Congresses.2.Materials-Testing-Congresses.I.Brown,Kevin R.,1941-II.Baratta,F.I.III.ASTM Committee E-24 on Fracture Testing.IV.Series:ASTM special technical publication;1172.TA409.C444 1992 620.1 126-dc20 92-24966 CIP Copyright?9 1992 AMERICAN SOCIETY FOR TESTING AND MATERIALS,Philadelphia,PA.All rights reserved.This material may not be reproduced or copied,in whole or in part,in any printed,mechanical,electronic,film,or other distribution and storage media,without the written consent of the publisher.Photocopy Rights Authorization to photocopy items for internal or personal use,or the internal or personal use of specific clients,is granted by the AMERICAN SOCIETY FOR TESTING AND MATERIALS for users registered with the Copyright Clearance Center(CCC)Transactional Reporting Service,provided that the base fee of$2.50 per copy,plus$0.50 per page is paid directly to CCC,27 Congress St.,Salem,MA 01970;(508)744-3350.For those organizations that have been granted a photocopy license by CCC,a separate system of payment has been arranged.The fee code for users of the Transactional Reporting Service is 0-8031-1480-X/92$2.50+.50.Peer Review Policy Each paper published in this volume was evaluated by three peer reviewers.The authors addressed all of the reviewers comments to the satisfaction of both the technical editor(s)and the ASTM Committee on Publications.The quality of the papers in this publication reflects not only the obvious efforts of the authors and the technical editor(s),but also the work of these peer reviewers.The ASTM Committee on Publications acknowledges with appreciation their dedication and contribution to time and effort on behalf of ASTM.Printed in Ann Arbor,MI August 1992 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:08:26 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Foreword This publication,Chevron-Notch Fracture Test Experience:Metals and Non-Metals,contains papers presented at the symposium of the same name held in Indianapolis,Indiana on 6 May 1991.The symposium was sponsored by ASTM Committee E-24 on Fracture Testing.Symposium co-chairmen were Kevin R.Brown,Kaiser Aluminum and Chemical Corp.,Pleasanton,CA,and Francis I.Baratta,Army Materials,Technology Lab,Watertown,MA.Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:08:26 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Contents Overview STUDIES OF THE TEST METHOD Some Observations in Fracture Toughness and Fatigue Testing with Chevron-Notched Specimens-JONATHAN A.SALEM,JOHN L.SHANNON,JR.,AND MICHAEL G.JENKINS Applicability of the Short Rod Fracture Toughness Test to New Microalloyed Bar Steels-T.c.TSCHANZ,D.K.MATLOCK,AND G.KRAUSS Specimen Size and Orientation Effects in Chevron-Notch Fracture Testing of Aluminum Alloy Plate-J.MORRISON AND K.J.KARISALLEN Analysis of Some Compliance Calibration Data for Chevron-Notch Bar and Rod Specimens-THOMAS W.ORANGE,RAYMOND T.BUBSEY,WILLIAM S.PIERCE,AND JOHN L.SHANNON,JR.Fracture Toughness Evaluation of Ceramic Bonds Using a Chevron-Notch Disk Specimen-A.R.ROSENFIELD AND B.S.MAJUMDAR Fracture Toughness of Composite Laminates and Metallic Materials Using a Modified CNSB Specimen-JAMES P.LUCAS 26 43 54 63 74 APPLICATIONS TO METALLIC MATERIALS Fracture Toughness and Fractography of Corroded Dental Amalgams-HERBERT J.MUELLER Aluminum-Lithium Alloys:Evaluation of Fracture Toughness by Two Test Standards,ASTM Method E 813 and E 1304-PATRICK T.PURTSCHER,J.DAVID McCOLSKEY,AND ELIZABETH S.DREXLER Use of the Chevron-Notched Short Bar Test to Guarantee Fracture Toughness for Lot Release in Aluminum Alloys-JACK W.BRAY 91 110 131 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:08:26 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Using Chevron-Notch,Short-Bar Specimens for Measuring the Fracture Toughness of a Martensitic Stainless Steel at High Hardness-CHARLES