ASTM_F_467_-_13e2.pdf

Designation:F467132Standard Specification forNonferrous Nuts for General Use1This standard is issued under the fixed designation F467;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1NOTETable 2 was editorially corrected in February 2014.2NOTE17.1 was editorially corrected in May 2014.1.Scope*1.1 This specification covers the requirements for commer-cial wrought nonferrous nuts 0.250 to 1.500 in.inclusive indiameter in a number of alloys in common use and intended forgeneral service applications.1.2 Applicable bolts,cap screws,and studs for use with nutscovered by this specification are covered by SpecificationF468.1.3 The values stated in inch-pound units are to be regardedas standard.No other units of measurement are included in thisstandard.NOTE1This specification is the inch-pound companion to Specifica-tion F467M;therefore,no SI equivalents are presented in the specification.2.Referenced Documents2.1 ASTM Standards:2B154 Test Method for Mercurous Nitrate Test for CopperAlloysB574 Specification for Low-Carbon Nickel-Chromium-Molybdenum,Low-CarbonNickel-Molybdenum-Chromium,Low-CarbonNickel-Molybdenum-Chromium-Tantalum,Low-Carbon Nickel-Chromium-Molybdenum-Copper,andLow-CarbonNickel-Chromium-Molybdenum-Tungsten Alloy RodD3951 Practice for Commercial PackagingE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base AlloysE38 Methods for Chemical Analysis of Nickel-Chromiumand Nickel-Chromium-Iron Alloys(Withdrawn 1989)3E53 Test Method for Determination of Copper in UnalloyedCopper by GravimetryE54 Test Methods for Chemical Analysis of Special Brassesand Bronzes(Withdrawn 2002)3E55 Practice for Sampling Wrought Nonferrous Metals andAlloys for Determination of Chemical CompositionE62 Test Methods for Chemical Analysis of Copper andCopperAlloys(Photometric Methods)(Withdrawn 2010)3E75 Test Methods for Chemical Analysis of Copper-Nickeland Copper-Nickel-Zinc Alloys(Withdrawn 2010)3E76 Test Methods for Chemical Analysis of Nickel-CopperAlloys(Withdrawn 2003)3E92 Test Method for Vickers Hardness of Metallic Materials(Withdrawn 2010)3E101 Test Method for SpectrographicAnalysis ofAluminumand Aluminum Alloys by the Point-to-Plane Technique(Withdrawn 1996)3E120 Test Methods for Chemical Analysis of Titanium andTitanium Alloys(Withdrawn 2003)3E165 Practice for Liquid Penetrant Examination for GeneralIndustryE227 Test Method for Optical Emission SpectrometricAnalysis of Aluminum and Aluminum Alloys by thePoint-to-Plane Technique(Withdrawn 2002)3E354 Test Methods for Chemical Analysis of High-Temperature,Electrical,Magnetic,and Other Similar Iron,Nickel,and Cobalt AlloysE478 Test Methods for Chemical Analysis of Copper AlloysE1409 Test Method for Determination of Oxygen and Nitro-gen in Titanium and Titanium Alloys by Inert Gas FusionF468 Specification for Nonferrous Bolts,Hex Cap Screws,Socket Head Cap Screws,and Studs for General Use1This specification is under the jurisdiction of ASTM Committee F16 onFasteners and is the direct responsibility of Subcommittee F16.04 on NonferrousFasteners.Current edition approved April 1,2013.Published May 2013.Originallyapproved in 1976.Last previous edition approved in 2006 as F467 081.DOI:10.1520/F0467-13E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 F606 Test Methods for Determining the Mechanical Proper-ties of Externally and Internally Threaded Fasteners,Washers,Direct Tension Indicators,and RivetsF1470 Practice for Fastener Sampling for Specified Me-chanical Properties and Performance Inspection2.2 ASME Standards:4B 1.1 Unified Inch Screw Threads(UN and UNR ThreadForm)B 18.2.2 Square and Hex Nuts3.Ordering Information3.1 Orders for nuts under this specification shall include thefollowing information:3.1.1 Quantity(number of pieces of each item and size);3.1.2 Name of item;3.1.3 Size(diameter and threads per inch);3.1.4 Alloy number(Table 1);3.1.5 Stress relieving,if required(4.2.3);3.1.6“Shipment lot”testing,as required(Section 9);3.1.7 Source inspection,if required(Section 14);3.1.8 Certificate of compliance or test report,if required(Section 16)