分享
ASTM_F_2155_-_01_2009.pdf
下载文档

ID:189948

大小:837.41KB

页数:15页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_F_2155_ _01_2009
Designation:F215501(Reapproved 2009)Standard Specification forPerformance of Hasps and Other Attachment Devices forPadlocks or Seals1This standard is issued under the fixed designation F2155;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification describes and grades various levels ofperformance to provide users of the standard with criteria uponwhich to select suitable hasps and other attachment devices.Noeffort has been made to include criteria for specially madehasps used by the Department of Defense or other highlysensitive applications.1.2 The tests described are laboratory tests,and althoughthey simulate field conditions as to attacks,they do notduplicate these conditions.Tests described are repeatable in thelaboratory.1.3 Some users of this standard may wish to use hasps thathave special attributes not related to security.1.4 The values stated in SI units are to be regarded as thestandard.The inch-pound units given in parentheses areprovided for information only.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.2.Referenced Documents2.1 ASTM Standards:2F883 Performance Specification for Padlocks3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 attachment device,nan item consisting of any num-ber of members that act in combination with a padlock or sealto provide a locking security system.3.1.2 fixed hasp,na combination of elements that,whenaligned,provide holes though which a padlock shackle or sealmay pass to secure the elements.3.1.3 hasp,nan attachment device having a hinged orfixed strap that engages a hasp staple to provide for theattachment of a padlock or seal.3.1.4 hasp staple,nan eye-or U-shaped element that isengaged by the slotted strap of a hasp and provides for theattachment of a padlock or seal.3.1.5 hasp staple pad,na component of a hasp staple thatprovides a fastening medium for attachment of the hasp stapleto the mounting surface.3.1.6 hasp strap,na component of a hasp that engages ahasp staple.3.1.7 hasp strap pad,na component of a hasp strap thatprovides a fastening medium for attachment of the hasp to themounting surface.3.1.8 hinged hasp,na hasp that includes a hasp strap,ahasp strap pad,a hasp staple,and a hasp staple pad incombination such that the hasp strap,when closed,engages thehasp staple,providing for the attachment of a padlock or sealto cause the assembly to be latched and locked or sealed intoa secure system.3.1.9 latch,nan item consisting of any number of mem-bers that act in combination to fasten separate elements into aconnected whole,and provides for the unfastening of thiswhole.3.1.10 latching attachment device,nan attachment devicethat includes a latching feature that permits the assembly toremain engaged without the use of a padlock or seal.3.1.11 latching hasp,na hasp that includes a latchingfeature that permits the strap to remain engaged with the haspstaple without the use of a padlock or seal.3.1.12 rotating hasp staple,na hasp staple that is free toturn in its pad,generally to provide a latching function byengaging the hasp strap,or to resist a torsional attack.4.General Requirements4.1 Tolerances:1This specification is under the jurisdiction of ASTM Committee F12 onSecurity Systems and Equipment and is the direct responsibility of SubcommitteeF12.50 on Locking Devices.Current edition approved Nov.1,2009.Published March 2010.Originallyapproved in 2001.Last previous edition approved in 2001 as F2155 01.DOI:10.1520/F2155-01R09.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.1.1 Fixture TolerancesAll tolerances shall follow stan-dard machining practices unless otherwise specified.4.1.2 Test Setup Tolerances:4.1.2.1 Force61%of working range.4.1.2.2 Height63 mm(0.12 in.).4.1.2.3 Torque4%of reading.4.1.2.4 Weight610 g(0.02 lb).4.2 TemperatureAll tests shall be conducted between16C and 27C(61F and 81F).4.3 Test ReportsAll test reports shall be dated.5.Test Specimens5.1 Select specimens at random from the manufacturersfinished stock of each size and model being certified by themanufacturer.5.2 Select four hasps for the forcing tests.6.Preparation of Apparatus6.1 Tensile Loading D

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开