分享
ASTM_F_2885_-_11.pdf
下载文档

ID:189926

大小:105.92KB

页数:5页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_F_2885_ _11
Designation:F288511Standard Specification forMetal Injection Molded Titanium-6Aluminum-4VanadiumComponents for Surgical Implant Applications1This standard is issued under the fixed designation F2885;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the chemical,mechanical,andmetallurgical requirements for two types of metal injectionmolded(MIM)titanium-6aluminum-4vanadium componentsto be used in the manufacture of surgical implants.1.2 The Type 1 MIM components covered by this specifi-cation may have been densified beyond their as-sintereddensity by post sinter processing.1.3 Values in either inch-pound or SI are to be regardedseparately as standard.The values stated in each system maynot be exact equivalents;therefore,each system shall be usedindependent of the other.Combining values from the twosystems may result in non-conformance with the specification.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2B243 Terminology of Powder MetallurgyB311 Test Method for Density of Powder Metallurgy(PM)Materials Containing Less Than Two Percent PorosityB923 Test Method for Metal Powder Skeletal Density byHelium or Nitrogen PycnometryE3 Guide for Preparation of Metallographic SpecimensE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE165 Practice for Liquid Penetrant Examination for GeneralIndustryE407 Practice for Microetching Metals and AlloysE539 Test Method forAnalysis of TitaniumAlloys by X-RayFluorescence SpectrometryE1409 Test Method for Determination of Oxygen and Nitro-gen in Titanium and Titanium Alloys by the Inert GasFusion TechniqueE1447 Test Method for Determination of Hydrogen in Tita-nium and Titanium Alloys by Inert Gas Fusion ThermalConductivity/Infrared Detection MethodE1941 Test Method for Determination of Carbon in Refrac-tory and Reactive Metals and TheirAlloys by CombustionAnalysisE2371 Test Method for Analysis of Titanium and TitaniumAlloys by Atomic Emission Plasma SpectrometryE2626 Guide for Spectrometric Analysis of Reactive andRefractory MetalsF601 Practice for Fluorescent Penetrant Inspection of Me-tallic Surgical ImplantsF629 Practice for Radiography of Cast Metallic SurgicalImplantsF1108 Specification for Titanium-6Aluminum-4VanadiumAlloy Castings for Surgical Implants(UNS R56406)F1472 Specification for Wrought Titanium-6Aluminum-4Vanadium Alloy for Surgical Implant Applications(UNSR56400)SI 10 American National Standard for Use of the Interna-tional System of Units(SI):The Modern Metric System2.2 ISO Standards:3ISO 5832-3 Implants for SurgeryMetallic MaterialsPart3:Wrought Titanium 6-Aluminum 4-Vanadium AlloyThird EditionISO 6892 Metallic MaterialsTensile Testing at AmbientTemperatureISO 9001 Quality Management SystemsRequirements2.3 Aerospace Material Specifications:4AMS 2249 Chemical Check Analysis Limits,Titanium andTitanium Alloys1This specification is under the jurisdiction of ASTM Committee F04 onMedical and Surgical Materials and Devices and is the direct responsibility ofSubcommittee F04.12 on Metallurgical Materials.Current edition approved March 1,2011.Published March 2011.DOI:10.1520/F288511.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.4Available from American Society for Quality(ASQ),600 N.Plankinton Ave.,Milwaukee,WI 53203,http:/www.asq.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.4 MPIF Standards:5Standard 10 Determination of the Tensile Properties ofPowder Metallurgy MaterialsStandard 42 Determination of Density of Compacted orSintered Powder Metallurgy ProductStandard 50 Preparing and Evaluating Metal InjectionMolded Sintered/Heat-Treated Tension SpecimensStandard 63 Density Determinations of MIM Components(Gas Pycnometry)Standard 64 Terms Used in Metal Injection Molding3.Terminology3.1 Definitions of powder metallurgy and MIM terms can befound in Terminology B243 and MPIF Standard 64.Additionaldescriptive information is available in the Related MaterialSection of Vol.02.05 of the Annual Book of ASTM Standards.3.2 Definitions of Terms Specific

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开