_STP_1157-1992.pdf

STP 1157 Cyclic Deformation,Fracture,and Nondestructive Evaluation of Advanced Materials M.R.Mitchell and Otto Buck,editors ASTM Publication Code Number(PCN)04-011570-30 ASTM 1916 Race Street Philadelphia,PA 19103 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:00:03 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Library of Congress Cataloging-in-Publication Data Cyclic deformation,fracture,and nondestructive evaluation of advanced materials/M.R.Mitchell and Otto Buck,editors.(STP;1157)Based on papers presented at a symposium held in San Antonio,Tex.Nov.12-13,1990.ASTM publication code number(PCN).Includes bibliographical references and index.ISBN 0-8031-1444-3 1.Composite materials-Fatigue-Congresses.2.Non-destructive testing-Congresses.I.Mitchell,M.R.(Michael R.),1941-II.Buck,Otto.III.Series:ASTM special technical publication;1157 TA418.9.C6C83 1992 620.1 186-dc20 92-16045 CIP Copyright?9 1992 AMERICAN SOCIETY FOR TESTING AND MATERIALS,Phil-adelphia,PA.All rights reserved.This material may not be reproduced or copied,in whole or in part,in any printed,mechanical,electronic,film,or other distribution and storage media,without the written consent of the publisher.Photocopy Rights Authorization to photocopy items for internal or personal use,or the internal or personal use of specific clients,is granted by the AMERICAN SOCIETY FOR TESTING AND MATERIALS for users registered with the Copyright Clearance Center(CCC)Transac-tional Reporting Service,provided that the base fee of$2,50 per copy,plus$0.50 per page is paid directly to CCC,27 Congress St.,Salem,MA 01970;(508)744-3350.For those organizations that have been granted a photocopy license by CCC,a separate system of payment has been arranged.The fee code for users of the Transactional Reporting Service is 0-8031-1444-3/92$2.50+.50.Peer Review Policy Each paper published in this volume was evaluated by three peer reviewers.The authors addressed all of the reviewers comments to the satisfaction of both the technical editor(s)and the ASTM Committee on Publications.The quality of the papers in this publication reflects not only the obvious efforts of the authors and the technical editor(s),but also the work of these peer reviewers.The ASTM Committee on Publications acknowledges with appreciation their dedication and contribution to time and effort on behalf of ASTM.Printed in Ann Arbor,MI Aug.1992 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:00:03 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Foreword This publication,Cyclic Deformation,Fracture,and Nondestructive Evaluation of Ad-vanced Materials,contains papers presented at the symposium of the same name held in San Antonio,Texas,12-13 November 1990.The symposium was sponsored by ASTM Committee E9 on Fatigue and its Subcommittees,E9.03 on Fatigue of Advanced Materials and E9.01.07 on Research on Nondestructive Evaluation of Advanced Materials.M.R.Mitchell,Rockwell International,and Otto Buck,Iowa State University,presided as sym-posium chairmen and are editors of this publication.Copyright by ASTM Intl(all rights reserved);Wed Dec 23 19:00:03 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Contents Overview Cyclic Fatigue of Aiumnia-c.-K.J.LIN,T.A.MAYER,AND D.F.SOCIE Fatigue Crack Growth in Ceramics and Ceramic Matrix Composites-R.JOHN AND N.E.ASHBAUGH Fatigue Test Methodology and Results for Ceramic Matrix Composites at Room and Elevated Temperatures-L.M.BUTKUS,L.P.ZAWADA AND G.A.HARTMAN Small-Crack Behavior and Safety-Critical-Design Criteria for Cyclic Fatigue in Mg-PSZ Ceramics-A.A.STEFFEN,R.H.DAUSKARDT,AND R.O.RITCHIE Modeling Crack Growth Resistance in Ceramics and Ceramic-Matrix Composites-J.LLORCA AND M.ELICES Thermomechanical Cyclic Deformation of Metal-Matrix Composites-M.KARAYAKA AND H.SEHITOGLU Fatigue Characteristics of Heavily Cold-Roiled Cu-20Nb-B.s.BINER AND W.A.SPITZIG Effect of Tensile Mean Stress on Fatigue Behavior of Single-Crystal and Directionally Solidified Superalloys-s.KALLURI AND M.A,MCGAW Mechanical Properties of Amorphous and Roll-Drawn Polypropylene-D.MCCAMMOND,A.N.SINCLAIR AND L.A.SINCLAIR The Influence of Constituent Properties on the Compression Behavior of Laminates with Discontinuities-D.L.CRANE,W.L.BRADLEY,AND D.L.BARRON Cyclic Creep Effects in Single-Overlap Bonded Joints Under Constant-Amplitude Testing-R.A.CHERNENKOFF Interpretation of Laboratory Test Information for Residual Strength and Life Prediction of Composite Systems-K.L.REIFSNIDER Crack Resistance,Fracture Toughness,and Instability in Damage-Tolerant Aluminum-Lithium Ailoys-R.J.H.WANHILL,L.SCHRA,AND W.G.J.T HART Ultrasonic Wave Technique to Assess Cyclic-Load Fatigue Damage in Silicon-Carbide Whisker