ASTM_F_2648_-_F_2648M_-_13.pdf

Designation:F2648/F2648M13Standard Specification for2 to 60 inch 50 to 1500 mm Annular Corrugated ProfileWall Polyethylene(PE)Pipe and Fittings for Land DrainageApplications1This standard is issued under the fixed designation F2648/F2648M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers requirements and test methodsfor annular corrugated profile wall polyethylene pipe andfittings with an interior liner.The inside diameters covered are2 to 60 in.50 to 1500 mm.1.2 The requirements of this specification are intended toprovide non-pressure(gravity flow)pipe and fittings suitablefor underground use for subsurface and land drainage systems,which do not operate under surcharge pressure heads.NOTE1Pipe and fittings produced in accordance with this specifica-tion are be installed in compliance with Practice D2321 or Practice F449based on diameter limitations within the respective standards.NOTE2Subsurface and land drainage systems pertain principally tonon-municipal or private facilities for water table control,storm drainageand agricultural drainage applications.The products supplied under thisspecification are not intended for any sanitary sewer or municipal stormsewer applications.1.3 This specification covers pipe and fittings with aninterior liner using an annular exterior corrugated profile(Fig.1).1.4 This specification permits the use of recycled materialsfor pipe in accordance with the requirements in Section 5.1.5 UnitsThe values stated in either inch-pound units orSI units are to be regarded separately as standard.The valuesstated in each system may not be exact equivalents:therefore,each system shall be used independently of the other.Combin-ing values from the two systems may result in non-conformance with the standard.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsD4218 Test Method for Determination of Carbon BlackContent in Polyethylene Compounds By the Muffle-Furnace TechniqueD5630 Test Method for Ash Content in PlasticsD7209 Guide for Waste Reduction,Resource Recovery,andUse of Recycled Polymeric Materials and Products(With-drawn 2015)3D7399 Test Method for Determination of the Amount ofPolypropylene(PP)in Polypropylene/LDPE Mixtures Us-ing Infrared Spectrophotometer(FTIR)F412 Terminology Relating to Plastic Piping SystemsF449 Practice for Subsurface Installation of CorrugatedPolyethylene Pipe for Agricultural Drainage or WaterTable ControlF2136 Test Method for Notched,Constant Ligament-Stress(NCLS)Test to Determine Slow-Crack-Growth Resis-tance of HDPE Resins or HDPE Corrugated Pipe1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.65 on LandDrainage.Current edition approved Jan.1,2013.Published January 2013.Originallyapproved in 2007.Last previous edition approved in 2010 as F2648/F2648M 10.DOI:10.1520/F2648_F2648M-11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.2 American Association of Highway and TransportationOffcials4(AASHTO)AASHTO LRFD Bridge Design Specifications2.3 Federal Standards:5Fed.Stds.No.123 Marking for Shipment(Civil Agencies)2.4 Military Standard:6MIL-STD-129 Marking for Shipment and Storage2.5 NCHRP(National Cooperative Highway Research Pro-gram)Report:7NCHRP Report 631 Updated Test and Design Methods forThermoplastic Drainage Pipe3.Terminology3.1 Definitions are in accordance with Termino