分享
ASTM_F_3219_-_19.pdf
下载文档

ID:189117

大小:123.58KB

页数:6页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_F_3219_ _19
Designation:F321919Standard Specification for3 to 30 in.(75 To 750 mm)Polypropylene(PP)CorrugatedSingle Wall Pipe and Fittings1This standard is issued under the fixed designation F3219;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers requirements and test methodsformaterials,dimensions,workmanship,elongation,brittleness,pipe stiffness,and markings for single wall corru-gated polypropylene(PP)pipe and fittings.It covers nominalsizes 3 in.through 30 in.(75 mm through 750 mm)1.2 The corrugated polypropylene pipe and fittings are foruse in non-pressure applications where soil-tight joints areacceptable,such as leach field effluent disposal,and drainageapplications such as land,roads,foundations,agricultural,andlandfill.Products meeting this specification are not suitable forapplications requiring water-tight joints unless the manufac-turer offers such joints as an option.NOTE1Watertight joints,when requested or specified,should meet a10.8 psi(74 kPa)laboratory internal and external pressure in accordancewith Specification D3212 and should utilize a bell and spigot design witha gasket that complies with Specification F477.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D256 Test Methods for Determining the Izod PendulumImpact Resistance of PlasticsD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD1238 Test Method for Melt Flow Rates of Thermoplasticsby Extrusion PlastometerD1505 Test Method for Density of Plastics by the Density-Gradient TechniqueD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Practice for Determination of the Impact Resistanceof Thermoplastic Pipe and Fittings by Means of a Tup(Falling Weight)D3212 Specification for Joints for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsD3895 Test Method for Oxidative-Induction Time of Poly-olefins by Differential Scanning CalorimetryD4101 Classification System and Basis for Specification forPolypropylene Injection and Extrusion MaterialsF412 Terminology Relating to Plastic Piping SystemsF449 Practice for Subsurface Installation of CorrugatedPolyethylene Pipe for Agricultural Drainage or WaterTable ControlF477 Specification for Elastomeric Seals(Gaskets)for Join-ing Plastic Pipe1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.65 on LandDrainage.Current edition approved April 1,2019.Published April 2019.Originallyapproved in 2017.Last previous edition approved in 2018 as F321918.DOI:10.1520/F3219192For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 2.2 AASHTO Standard:3AASHTO LRFD Bridge Design Specifications3.Terminology3.1 Defin

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开