ASTM_F_2933_-_19.pdf

Designation:F293319Standard Consumer Safety Specification forCrib Mattresses1This standard is issued under the fixed designation F2933;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This consumer safety specification establishes designrequirements,testing requirements and methods,and require-ments for labeling for full-size crib mattresses,non-full-sizecrib mattresses,and after-market mattresses for play yards andnon-full size cribs.1.2 No crib mattress produced after the approval date of thisconsumer safety specification shall,either by label or othermeans,indicate compliance with this specification unless itconforms to all requirements contained herein.1.3 UnitsThe values stated in inch-pound units are to beregarded as the standard.The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D3359 Test Methods for Rating Adhesion by Tape TestF406 Consumer Safety Specification for Non-Full-SizeBaby Cribs/Play YardsF1169 Consumer Safety Specification for Full-Size BabyCribsF2194 Consumer Safety Specification for Bassinets andCradles2.2 Federal Standards:316 CFR 1303 Ban of Lead-Containing Paint and CertainConsumer Products Bearing Lead-Containing Paint16 CFR 1500.48 Technical Requirements for Determining aSharp Point in Toys and Other Articles for Use byChildren Under Eight Years of Age16 CFR 1500.49 Technical Requirements for Determining aSharp Metal or Glass Edge in Toys or Other ArticlesIntended for Use by Children Under Eight Years of Age16 CFR 1501 Method for Identifying Toys and Other Ar-ticles Intended for Use by Children Under Three Years ofAge Which Present Choking,Aspiration or IngestionHazards Because of Small Parts16 CFR 1219 Requirements for Full-Size Baby Cribs16 CFR 1220 Requirements for Non-Full-Size Baby Cribs16 CFR 1632 Standard for the Flammability of Mattressesand Mattress Pads16 CFR 1633 Standard for the Flammability(Open Flame)of Mattress SetsConsumer Product Safety Improvement Act of 2008(CP-SIA)3.Terminology3.1 Definitions:3.1.1 after-market mattress for play yard or non-full-sizecrib,na mattress sold or distributed for a play yard ornon-full-sized crib.3.1.1.1 DiscussionThis does not include a replacementmattress provided or sold by an original equipment manufac-turer(OEM)if,and only if,it is equivalent with respect todimensions,and specifications to the mattress that was pro-vided with the original product.3.1.2 conspicuous,adjvisible,when the mattress is beinghandled by a consumer.3.1.3 core,nmain support system that may be present in amattress,such as springs,foam,hair block,or resilient filling.1This consumer safety specification is under the jurisdiction of ASTM Commit-tee F15 on Consumer Products and is the direct responsibility of SubcommitteeF15.66 on Crib Mattresses.Current edition approved June 15,2019.Published July 2019.Originallyapproved in 2013.Last previous edition approved in 2018 as F2933 18.DOI:10.1520/F2933-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from the U.S.Government Printing Office,Superintendent ofDocuments,732 N.Capital St.,NW,Washington,DC 20402-0001.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.1.4 crib,nbed that is designed to provide sleepingaccommodations for an infant which have specific interiordimensions as determined by it being either a full size ornon-full size crib:3.1.4.1 full size crib,n5238658in.(1330 6 16 mm);Width 28 658in.(711 6 16 mm)(as defined in 16 CFR 1219and Consumer Safety Specifi