ASTM_F_1533_-_01_2009.pdf

Designation:F153301(Reapproved 2009)Standard Specification forDeformed Polyethylene(PE)Liner1This standard is issued under the fixed designation F1533;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers requirements and test methodsfor materials of deformed PE liner intended for the rehabilita-tion of gravity flow and nonpressure pipelines.This applicationis for municipal sewage,storm water,industrial process liquidsand effluents,conduit,and ducts.This renewal process involvesinstalling a deformed liner into an existing pipeline,conduit,orduct,then reforming the liner with heat and pressure to fittightly to the bore of the original pipeline,conduit,or duct.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.In referee decisions,inch-pound units shall be used.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1693 Test Method for Environmental Stress-Cracking ofEthylene PlasticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2837 Test Method for Obtaining Hydrostatic Design Basisfor Thermoplastic Pipe Materials or Pressure Design Basisfor Thermoplastic Pipe ProductsD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsF412 Terminology Relating to Plastic Piping SystemsF1248 Test Method for Determination of EnvironmentalStress Crack Resistance(ESCR)of Polyethylene Pipe(Withdrawn 2007)32.2 Federal Standard:Fed.Std.No.123 Marking for Shipment(Civil Agencies)42.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage43.Terminology3.1 Definitions:3.1.1 Unless otherwise indicated,definitions are in accor-dance with Terminology F412,and abbreviations are in accor-dance with Terminology D1600.3.1.2 deformed linerpolyethylene pipe manufactured in adeformed shape that reduces the cross-sectional area forinsertion and rehabilitation of nonpressure pipelines,conduits,and ducts.(See Fig.1.)3.1.3 reformed linera reformed pipe is a sample for testpurposes formed when the deformed pipe has been insertedinto a given casing pipe and rerounded with heat and pressureto fit snugly to the casing pipe taking a given cross-section,inaccordance with Sections 5 and 6.(See Fig.1.)4.Materials4.1 Material requirements are applicable only to materialsprior to extrusion into the liner.Post-extrusion product require-ments are presented in Section 6.4.2 Material ClassificationsPolyethylene materials allow-able for use in the manufacture of polyethylene liner under this1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.26 on OlefinBased Pipe.Current edition approved Dec.1,2009.Published March 2010.Originallyapproved in 1994.Last previous edition approved in 2001 as F1533 01.DOI:10.1520/F1533-01R09.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 specification shall have a Plastic Pipe Institute(PPI)5recom-mended Hydrostatic Design Basis in accordance with Table 1and shall have a minimum classification in accordance withSpecification D3350,as shown in Table 2.4.3 Rework MaterialClean,rework material,meeting re-quirements in 4.2,and generated from the manufacturers ownpipe production,may be used by the same manufacturer,withmaterial meeting requirements in 4.2 in any combination,aslong as the liner produced meets all of the requirements of thisspecification for the pipe designated.5.Sampling5.1