ASTM_F_1193_-_16.pdf

Designation:F119316Standard Practice forQuality,Manufacture,and Construction of AmusementRides and Devices1This standard is issued under the fixed designation F1193;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice establishes the minimum requirements fora quality assurance program and the manufacturing of amuse-ment rides and devices(including major modifications).1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2E543 Specification for Agencies Performing NondestructiveTestingF770 Practice for Ownership,Operation,Maintenance,andInspection of Amusement Rides and DevicesF1950 Specification for Physical Information to be Trans-ferred With Used Amusement Rides and Devices(With-drawn 2008)3F2291 Practice for Design ofAmusement Rides and Devices2.2 AWS Standards:4As applicable.2.3 ASME Standards:5As applicable.2.4 ASNT Document:6Recommended Practice SNT-TC-1A Personnel Qualifica-tion and Certification in Nondestructive Testing3.Significance and Use3.1 The purpose of this practice is to provide the minimummanufacturing requirements for amusement rides and devicesand to provide the minimum requirements for a written qualityassurance program for an amusement ride or devicemanufacturer,or component supplier.This is not intended toinclude suppliers of off-the-shelf components(for example,fasteners,electrical wire,etc.).4.Drawing Control Procedure4.1 A procedure shall be in effect so that appropriatemanufacturing drawings,their engineering revisions,and re-lated documents are utilized.5.Material and Component Control Procedure5.1 A procedure shall be in effect so that materials,processes,and components,including raw materials,are inaccordance with the engineering specifications.5.1.1 This procedure shall provide the purchasing agentwith all the information required to order appropriate material.5.1.2 A receiving procedure shall be in effect so thatincoming material and components are checked against thepurchasing specifications.5.1.3 A procedure shall be in effect so that material in stockcan be properly identified for future use.5.1.4 Documentation on any material,process,or compo-nents certified shall be filed for reference.6.Manufacturing6.1 Amusement ride and device components and systemsshall be manufactured and assembled in accordance with thedesigner/engineer specified criteria.6.2 Changes to the designer/engineer specified criteria shallbe documented and approved by the designer/engineer or aqualified engineer before components,subassemblies,or sys-tems are placed into use.6.3 Quality Assurance Program:6.3.1 The manufacturer of an amusement ride or deviceshall have a written quality assurance program as specified inPractice F1193 for use in conjunction with the design,manufacture,construction,modification,or reconditioning ofthe amusement ride or device.1This practice is under the jurisdiction ofASTM Committee F24 on AmusementRides and Devices and is the direct responsibility of Subcommittee F24.24 onDesign and Manufacture.Current edition approved Feb.15,2016.Published March 2016.Originallyapproved in 1988.Last previous edition approved in 2015 as F1193 15.DOI:10.1520/F1193-16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from The American Welding Society(AWS),550 NW LeJeune Rd.,Miami,FL 33126.5Available from American Society of Mechanical Engineers(ASME),ASMEInternational Headquarters,Three Park Ave.,New York,NY 10016-5990.6Available from TheAmerican Society for Nondestructive Testing(ASNT),P.O.Box 28518,1711 Arlingate Ln.,Columbus,OH 43228-0518.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.3.2Quality assurance documents,that is,materialcertifications,test reports,and inspection reports,shall beretained for a period of time as deemed appropriate by themanufacturers.7.Inspection7.1 A procedure shall be in effect so that appropriateinspectionsaremadeonmanufacturedpartsandsubassemblies,for conformance with the designer/engineerspecified criteria.7.2 A procedure shall be in effect so that appropriateinspections are made on purchased components.7.3 A procedure shall be in effect so that completedsubassemblies,or where practical,the assemble