ASTM_F_1006_-_86_2014e1.pdf

Designation:F100686(Reapproved 2014)1An American National StandardStandard Specification forEntrainment Separators for Use in Marine PipingApplications1This standard is issued under the fixed designation F1006;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEThe Keywords Section was editorially added in November 2014.1.Scope1.1 This specification covers the minimum requirements forthe pressure-temperature rating,testing,and making ofpressure-containing vessels for entrainment separators.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The following safety hazards caveat pertains only to thetest methods portion,Section 6,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ANSI Standards:2B2.1 Pipe Threads(Except Dryseal)B16.1 Cast Iron Pipe Flanges and Flanged FittingsB16.3 Malleable Iron Threaded Fittings,Class 150 and 300B16.4 Cast Iron Threaded Fittings,Class 125 and 250B16.5 Steel Pipe Flanges and Flanged FittingsB16.11 Forged Steel Fittings,Socket Welding and ThreadedB16.15 Cast Bronze Threaded Fittings,Class 150 and 300B16.24 Bronze Flanges and Flanged Fittings,Class 150 and300B16.25 Buttwelding EndsB16.31 Nonferrous Pipe Flanges2.2 ASME Standards:3SA278 Cast Gray Iron Pressure VesselsSA395-60 Cast Ductile IronBoiler and Pressure Vessel Code,Section VIIIBoiler and Pressure Vessel Code,Section II2.3 MSS Standards:4MSSSP-51 150 LB Corrosion Resistant Cast Flanges andFlanged Fittings2.4 Military Standards:5MIL-F-1183 Fittings Tube,Bronze,Cast(Silver Brazings)3.Definitions of Terms Specific to This Standard3.1 entrainment separatora mechanical device inserted ina pipeline which by centrifugal force,baffles,or other meanswill separate a liquid from a gas(vapor).3.2 hydrostatic testthe act of filling an entrainment sepa-rator vessel with water and applying internal pressure to allparts of the vessel.3.3 master gagethe calibrated gage used to verify theaccuracy of the test gage.This gage shall be recalibratedtraceable to the National Bureau of Standards.3.4 pressure ratingthe maximum working pressure of anentrainment separator when operated at a specific temperature.3.5 proof testthe act of filling an entrainment separatorvessel with water and applying internal pressure to all parts ofthe vessel for the purpose of causing yielding of the vessel andbursting of the vessel.1This specification is under the jurisdiction of Committee F25 on Ships andMarine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved Nov.1,2014.Published November 2014.Originallyapproved in 1986.Last previous edition approved in 2008 as F1006 86(2008).DOI:10.1520/F1006-86R14E01.2Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.3Available from American Society of Mechanical Engineers(ASME),ASMEInternational Headquarters,Two Park Ave.,New York,NY 10016-5990,http:/www.asme.org.4Available from Manufacturers Standardization Society of the Valve and FittingsIndustry(MSS),127 Park St.,NE,Vienna,VA 22180-4602,http:/www.mss-.5Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/www.dodssp.daps.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.6 temperature ratingsminimum and maximum tempera-tures at which the entrainment separator may be operated whileat specific pressures.3.7 test gagethe pressure gage that is used to check theinternal pressure of the entrainment separator.The test gageshall be calibrated at least annually or at any time it issuspected to be in error by a calibrated master gage.4.Materials and Manufacture4.1 The pressure-temperature ratings established under thisspecification are based upon the manufacturers usage of highquality materials produced under regular control of chemicaland physical properties by a recognized process.The manu-facturer shall be prepared to submit certification of compliance,verifying that his product has been so produced and that it hasbeen manufactured from material with chemical and physicalproperties at least equal to the requirements of the appropriatestandard or specification listed in 4.3 of this specification orSection II of the ASME Boiler and Pressure