ASTM_F_1336_-_15.pdf

Designation:F133615Standard Specification forPoly(Vinyl Chloride)(PVC)Gasketed Sewer Fittings1This standard is issued under the fixed designation F1336;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers requirements and test methodsfor fabricated or molded poly(vinyl chloride)(PVC)gasketedsewer fittings to be used with piping manufactured to Specifi-cations D3034,F679,F891 or F1760.Fabricated fittings maybe manufactured from pipe,or from a combination of pipe andinjection molded parts,or from injection molded parts.1.2 The requirements of this specification are to providefabricated or molded PVC gasketed fittings suitable for non-pressure drainage of sewage and surface water,as well asapplications involving subsurface drainage.NOTE1Industrial waste lines should be installed only with thespecific approval of the governing code authority when using chemicalsnot commonly found in drains and sewers or temperatures in excess of140F(60C),or both.1.3 Fittings produced to this specification are intended to beinstalled with pipe,in accordance with Practice D2321.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 The following precautionary caveat pertains to the testmethod portion only,Section 10,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2564 Specification for Solvent Cements for Poly(VinylChloride)(PVC)Plastic Piping SystemsD2749 Symbols for Dimensions of Plastic Pipe FittingsD3034 Specification for Type PSM Poly(Vinyl Chloride)(PVC)Sewer Pipe and FittingsD3212 Specification for Joints for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsF412 Terminology Relating to Plastic Piping SystemsF477 Specification for Elastomeric Seals(Gaskets)for Join-ing Plastic PipeF610/F610M Practice for Evaluating the Quality of MoldedPoly(Vinyl Chloride)(PVC)Plastic Pipe Fittings by theHeat Reversion TechniqueF656 Specification for Primers for Use in Solvent CementJoints of Poly(Vinyl Chloride)(PVC)Plastic Pipe andFittingsF679 Specification for Poly(Vinyl Chloride)(PVC)Large-Diameter Plastic Gravity Sewer Pipe and FittingsF891 Specification for Coextruded Poly(Vinyl Chloride)(PVC)Plastic Pipe With a Cellular CoreF913 Specification for Thermoplastic Elastomeric Seals(Gaskets)for Joining Plastic PipeF1760 Specification for Coextruded Poly(Vinyl Chloride)(PVC)Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content2.2 Federal Standard:Fed.Std.No.123 Marking for Shipment(Civil Agencies)32.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage31This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approved Nov.1,2015.Published December 2015.Originallyapproved in 1991.Last previous edition approved in 2007 as F1336 07.DOI:10.1520/F1336-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia,PA19111-5094 http:/quicksearch.dla.mil/*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.Terminology3.1 Definitions are in accordance with Terminology F412unless otherwise specified.3.1.1 Abbreviations are in accordance with TerminologyD1600,unless otherwise indicated.The abbreviation for poly-(vinyl chloride)plastic is PVC.The abbreviation for plasticsewer main is PSM.4.Materials and Manufacture4.1 Basic MaterialsThe pipe components for fabricatedfittings shall be made f