ASTM_F_1233_-_08_2013.pdf

Designation:F123308(Reapproved 2013)Standard Test Method forSecurity Glazing Materials And Systems1This standard is issued under the fixed designation F1233;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method sets forth procedures whose purpose islimited to the evaluation of the resistance of security glazingmaterials and systems against the following threats:1.1.1 Ballistic Impact,1.1.2 Blunt Tool Impacts,1.1.3 Sharp Tool Impacts,1.1.4 Thermal Stress,and1.1.5 Chemical Deterioration.NOTE1Specifically exempted from this test method are the use ofpower(motor or engine-driven)tools or devices,explosives,militaryordinance(excepting small arms)and tools,processes or devices requiringmore than two persons to transport and operate.1.2 The values stated in inch-pounds are to be regarded asthe standard.The values given in parentheses are for informa-tion only.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.For a specificwarning statement,see Warning in 10.1.1.6.2.Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA53/A53M Specification for Pipe,Steel,Black and Hot-Dipped,Zinc-Coated,Welded and SeamlessA574 Specification forAlloy Steel Socket-Head Cap ScrewsF1029 Guide for Selection of Physical Security Measures fora Facility(Withdrawn 2004)32.2 Other Documents:Sporting Arms and Ammunition Manufacturers Institute(SAAMI)Ammunition4United StatesMilitaryAmmunitionSpecificationsAmmunition5Federal Specification GGG-313UCold Chisel6American Iron and Steel Institute M-1020Structural Steel7UL 10BCFire Extinguisher83.Terminology3.1 Definitions:3.1.1 test director,nindividual identified by the indepen-dent testing laboratory as being responsible to complete thespecified tests as required and to document the results.4.Class4.1 Ballistic ClassBallistic tests and test results from thisstandard shall be classified by the following(see also Table 1):4.1.1 HG1 Handgun-LowAmmunition conforming toSAAMI specifications for caliber.38 Special,158 grain(10.2g),soft point,producing velocities of 875(625)ft/s(266(67)m/s)at 15 ft(4.5 m)from the muzzle.4.1.2 HG2 Handgun-Medium Soft PointAmmunitionconforming to SAAMI specifications for caliber.357 Magnum,158 grain(10.2 g),jacketed soft point,producing velocities of1400(650)ft/s(427(615)m/s)at 15 ft(4.5 m)from themuzzle.4.1.3 HG3 Handgun-Medium JacketedAmmunition con-forming to SAAMI specifications for caliber 9 mm,124 grain(8.0 g),full metal casing,producing velocities of 1250(650)ft/s(381(615)m/s)at 15 ft(4.5 m)from the muzzle.4.1.4 HG4 Handgun-HighAmmunition conforming toSAAMI specifications for caliber.44 Magnum,240 grain,leadgas check producing velocities of 1450(650)ft/s(442(615)m/s)at 15 ft(4.5 m)from the muzzle.1This test method is under the jurisdiction of Committee F12 on SecuritySystems and Equipmentand is the direct responsibility of Subcommittee F12.10 onSystems Products and Services.Current edition approved May 1,2013.Published July 2013.Originally approvedin 1989.Last previous edition approved in 2008 as F1233 08.DOI:10.1520/F1233-08R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from Sporting Arms and Ammunition Manufacturers Association(SAAMI),Box 1075,Riverside,CT 06878.5Available from Standardization Documents Order Desk,Bldg.4,Section D,700 Robbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.6Available from General Services Adm.,7th and D Sts.SW,Washington,DC20407.7Available from American Iron and Steel Institute,1000 16th St.NW,Washington,DC 20036.8Available from Underwriters Laboratories,Inc.,333 Pfingsten Rd.,Northbrook,IL 60062.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.1.5 SMG Submachine GunAmmunition conforming toSAAMI specifications for caliber 9 mm,124 grain(8.0 g),fullmetal casing producing velocities of 1400(650)ft/s(427(615)m/s)at 15 ft(4.5 m)from the muzzle.4.1.6 R1 Rifle-LightAmmunition conforming to U.S.Military specifications for caliber.223(5.56 mm)NATO,M193 ball producing velocities of 3250(650)ft/s(991(615)m/s)at 15 ft(4.5 m)from the muzzle.4.1.7 R2 Rifle-Heavy Soft PointAmmunition conformingto SAAMI specifications for caliber.30-06,180 grain(11.7 g)soft point producing velocitie