ASTM_F_1245_-_89_2012.pdf

Designation:F124589(Reapproved 2012)An American National StandardStandard Specification forFaucets,Single and Double,Compression and Self-ClosingType,Shipboard1This standard is issued under the fixed designation F1245;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 Thisspecificationcoverssingle-anddouble-compression and self-closing faucets for shipboard plumbinginstallations.1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.3 The following precautionary caveat pertains only to thetest methods portion,Section 10,of this standard.This stan-dard does not purport to address all of the safety concerns,ifany,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2B62 Specification for Composition Bronze or Ounce MetalCastingsB584 Specification for Copper Alloy Sand Castings forGeneral Applications2.2 American National Standards Institute Standard:3B1.1 Unified Inch Screw Threads(UN and UNR ThreadForm)2.3 Federal Specifications:4PPP-B-566 Boxes,Folding,PaperboardPPP-B-585 Boxes,Wood,WireboundPPP-B-591 Boxes,Shipping,Fiberboard,Wood-CleatedPPP-B-601 Boxes,Wood,Cleated-PlywoodPPP-B-621 Boxes,Wood,Nailed and Lock-CornerPPP-B-636 Box,Shipping,FiberboardPPP-B-676 Boxes,SetupQQ-N-290 Nickel Plating(Electrodeposited)QQ-C-320 Chromium Plating(Electrodeposited)2.4 Military Specification:4MIL-P-116 Preservation,Methods of2.5 Military Standards:4MIL-STD-105 Sampling Procedures and Tables for Inspec-tion by AttributesMIL-STD-129 Marking for Shipment and Storage2.6 Naval Sea Systems Command(NAVSEA):4NAVSEA Drawing 803-5959206 Faucet,MeteringNAVSEA Drawing 805-1623970 Unit,Lavatory for OfficersStation3.Classification3.1 Faucets shall be of the following types and classes asspecified(see 4.1):3.1.1 Type IStandard(bibb):3.1.1.1 Class ACompression,plain end.3.1.1.2 Class BCompression,hose end.3.1.1.3 Class CSelf-closing.3.1.2 Type IILavatory,self-closing,low spout.3.1.2.1 Class AFast-closing.3.1.2.2 Class BSlow-closing,depression type.3.1.3 Type IIIFolding lavatory,self-closing.3.1.4 Type IVElbow operated.3.1.5 Type VLavatory,combination water supply anddrain fixture.3.1.6 Type VICombination supply fixture swing spout foruse on galley sinks.3.1.7 Type VIISingle supply fixture swing spout for usewith steam kettles and urns.3.1.7.1 Class ASpout for overhead supply.3.1.7.2 Class BSpout for riser supply.3.1.8 Type VIIISupply fixture for pressed metal and shockmounted china lavatories.3.1.9 Type IXLavatory,combination water supply anddrain fixtures,depression type.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved May 1,2012.Published May 2012.Originallyapproved in 1989.Last previous edition approved in 2006 as F1245 89(2006).DOI:10.1520/F1245-89R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.4Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.Ordering Information4.1 Orders for equipment under this specification shallinclude the following information,as required,to describe theequipment adequately:4.1.1 ASTM designation and year of issue,4.1.2 Type and class of faucet required(see 3.1),4.1.3 Type of handle required(see 6.11),4.1.4 Marking required for handles(see 13.1),4.1.5 Size and weight of Type I faucet required(see 7.1),4.1.6 Overall dimensions for Type II faucets(see 7.2),4.1.7 Shank design for Type II,Class B faucets(see 6.2.3.2),4.1.8 Overall dimensions and position of inlet(side orbottom)for Type III faucets(see 7.3),4.1.9 Overall dimensions and whether spray is required forType IV faucets(see 6.4.1.3 and 7.4),4.1.10 Length of spout for Type VI fixtures(see 7.6.1),4.1.11 Whether escutcheon plates are provided for Type VIfaucets(see 6.6.3),4.1.12 Whether connections are other than14-in.nominalpipe size(NPS)(see 6.8.2.1),4.1.13 Sample size for examination and testing(see 10.1,10.2,and 11.1),and4.1.14 Optional requirements,if any(see SupplementaryRequi