ASTM_F_1077_-_95a_2002.pdf

Designation:F 1077 95a(Reapproved 2002)Standard Guide forSelection of Committee F16 Fastener Specifications1This standard is issued under the fixed designation F 1077;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide is intended to provide a rapid,easy to usemethod for identifying Committee F16 fastener specificationsand their applicable marking requirements.Selection is madeby product type(bolts,nuts,washers,etc.)and material(alloysteel,carbon steel,stainless steel,etc.)from Tables 1-5 asfollows:Table NumberInchMetricFerrous MetalsAlloy Steel13Carbon Steel13Weathering Steel13Non FerrousAluminum,CopperNickel,Titanium23Stainless Steels23OthersCoatings,Definitions,Test Methods,Surface44DiscontinuitiesMarking551.2 Table size limitations and the need for simplicity pro-hibit identifying the exact grade,type,condition,etc.,for allproduct/material combinations.The product specification mustbe reviewed prior to specifying fasteners on drawings orordering to properly and completely identify the fastener,andits available variations.2.Referenced Documents2.1 ASTM Standards:A 31 Specification for Steel Rivets and Bars for Rivets,Pressure Vessels2A 307 Specification for Carbon Steel Bolts and Studs,60 000 PSI Tensile Strength2A 325 Specification for Structural Bolts,Steel,HeatTreated,120/105 ksi Minimum Tensile Strength2A 325M Specification for High-Strength Bolts for Struc-tural Steel Joints Metric2A 354 Specification for Quenched and Tempered AlloySteel Bolts,Studs,and Other Externally Threaded Fasten-ers2A 394 Specification for Steel Transmission Tower Bolts,Zinc-Coated and Bare2A 449 Specification for Quenched and Tempered SteelBolts and Studs2A 489 Specification for Carbon Steel Lifting Eyes2A 490 Specification for Structural Bolts,Alloy Steel,HeatTreatment,150 ksi Minimum Tensile Strength2A 490M Specification for High-Strength Steel Bolts,Classes 10.9 and 10.9.3,for Structural Steel Joints Met-ric2A 502 Specification for Steel Structural Rivets3A 563 Specification for Carbon and Alloy Steel Nuts2A 563M Specification for Carbon and Alloy Steel NutsMetric2A 574 Specification for Alloy Steel Socket-Head CapScrews2A 574M Specification for Alloy Steel Socket-Head CapScrews Metric2A 687 Specification for High-Strength Nonheaded SteelBolts and Studs2C 514 Specification for Nails for the Application of Gyp-sum Board4F 432 Specification for Roof and Rock Bolts and Accesso-ries2F 436 Specification for Hardened Steel Washers2F 436M Specification for Hardened Steel Washers Metric2F 467 Specification for Nonferrous Nuts for General Use2F 467M Specification for Nonferrous Nuts for General UseMetric2F 468 Specification for Nonferrous Bolts,Hex Cap Screws,and Studs for General Use2F 468M Specification for Nonferrous Bolts,Hex CapScrews,and Studs for General Use Metric2F 541 Specification for Alloy Steel Eyebolts2F 547 Terminology of Nails for Use with Wood and Wood-Base Materials2F 568M Specification for Carbon andAlloy Steel ExternallyThreaded Metric Fasteners Metric21This guide is under the jurisdiction of ASTM Committee F16 on Fasteners andis the direct responsibility of Subcommittee F16.91 on Editorial.Current edition approved Oct.10,2002.Published July 2003.Originallyapproved in 1987.Last previous edition approved in 1995 as F 1077 95a.2Annual Book of ASTM Standards,Vol 01.08.3Discontinuedsee 1998 Annual Book of ASTM Standards,Vol 01.08.4Annual Book of ASTM Standards,Vol 04.01.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.F 592 Terminology of Collated and Cohered Fasteners andTheir Application Tools2F 593 Specification for Stainless Steel Bolts,Hex CapScrews,and Studs2TABLE 1Alloy,Carbon,and Weathering Steels,InchProductAAlloy SteelCarbon SteelWeatheringSteelsLowMediumMartensiticBoltsB:EyeF 541A 489General purpose:UTS 60KA 307 Gr A,BUTS 120,105,90KA 449 Type 1A 449 Type 2UTS 125,115KA 354 Gr BCUTS 150,140KA 354 Gr BDNon HeadedA 687Roof and RockF 432Structural:UTS 120,105KA 325 Type 1CA 325 Type 3UTS 150KA 490 Type 1A 490 Type 2A 490 Type 3Transmission towerA 394 Type 0A 394 Type 1A 394 Type 2A 394 Type 3Nails:Gypsum wallboardC 514NutsB:PL 69KA 563 Gr 0PL 100,90KA 563 Gr APL 133,120,116,105KA 563 Gr BPL 144KA 563 Gr CA 563 Gr C 3PL 150,135KA 563 Gr DPL 175,150KA 563 Gr DHPL 175KA 563 Gr DH3Rivets:General purposeA 502 Gr 1Pressure vesselA 31 Gr AA 31 Gr BStructuralA 502 Gr 1A 502 Gr 2A 502 Gr 3Screws:Hex capA 449 Type 1A 449 Type 2Socket headA 574Socket button and flat CSKF 835Socket setF 912Studs:UTS 58-80KA 307 Gr CUTS 60KA 307 Gr A,BUTS 120,105,90KA 449 Type 1A 449 Type 2UTS 125,115KA 354 Gr BCUTS 150,140KA 354 Gr BDUTS 150KA 687Washers:General Purpose,SoftF 844General Purpose,HardF 436F 436Load Ind