ASTM_F_1007_-_18.pdf

Designation:F100718An American National StandardStandard Specification forPipeline Expansion Joints of the Packed Slip Type forMarine Application1This standard is issued under the fixed designation F1007;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the design,manufacturing,andtesting of packed slip-type expansion joints used in pipelinesfor accommodating axial thermal growth or contraction fromthe pipeline carrying fluid.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2A53/A53M Specification for Pipe,Steel,Black and Hot-Dipped,Zinc-Coated,Welded and SeamlessA216/A216M Specification for Steel Castings,Carbon,Suit-able for Fusion Welding,for High-Temperature ServiceA285/A285M Specification for Pressure Vessel Plates,Car-bon Steel,Low-and Intermediate-Tensile StrengthB650 Specification for Electrodeposited Engineering Chro-mium Coatings on Ferrous Substrates2.2 ANSI Standards:3B16.5 Steel Pipe Flanges and Flanged FittingsB16.25 Buttwelding EndsB31.1 Power Piping2.3 ASME Standards:4Section V Nondestructive ExaminationSection VIII,Division 1 Pressure VesselsSection IX Welding and Brazing Qualifications2.4 AISI Standard:C-1018 Carbon Steel53.Classification3.1 The expansion joints shall be of the following types,styles,classes,and forms:3.1.1 Type 1Injectable semiplastic packing type,designedfor injecting packing under full-line pressure.3.1.2 Style IInternally externally guided with guides inte-gral with stuffing box.3.1.3 Style IIInternally externally guided with guidesintegral with stuffing box and with low-friction inserts at theguide surfaces.3.1.4 Class ISingle joint,single slip.3.1.5 Class IIDouble joint,double slip.3.1.6 Form IWeld end.3.1.7 Form IIFlanged end.3.1.8 Form IIIOther.4.Ordering Information4.1 Expansion joints shall meet all the requirements of thelatest issue of this specification.Where possible,the expansionjoint shall be the manufacturers standard commercial product.Additional or superior features that are not prohibited by thisspecification but which are a part of the manufacturersstandard product,shall be included with the expansion jointbeing offered.A standard commercial product is a product thathas been sold or is currently being offered for sale on thecommercial market through advertisements or manufacturerscatalogs,or brochures,and represents the latest productionmodel.4.2 Purchase order or inquiry for expansion joints to thisspecification shall specify the following:1This specification is under the jurisdiction of Committee F25 on Ships andMarine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved May 1,2018.Published May 2018.Originallyapproved in 1986.Last previous edition approved in 2014 as F1007 86(2014).DOI:10.1520/F1007-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.4Available from American Society of Mechanical Engineers(ASME),ASMEInternational Headquarters,Two Park Ave.,New York,NY 10016-5990,http:/www.asme.org.5Available from American Iron and Steel Institute(AISI),25 MassachusettsAve.,NW,Suite 800,Washington,DC 20001,http:/www.steel.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.2.1 Title,number,and latest revision of this specification.4.2.2 Style,class,and form required.4.2.3 Materials,other than standard as specified(see Section8).4.2.4 Service conditions shall specify the following:4.2.4.1 Maximum and minimum operating temperature(F).4.2.4.2 Maximum operating pressure(psig).4.2.4.3 Fluid handled.4.2.4.4 Corrosive condition