ASTM_F_1068_-_90_2012.pdf

Designation:F106890(Reapproved 2012)An American National StandardStandard Specification forDoors,Double,Gastight/Airtight,Individually Dogged,forMarine Use1This standard is issued under the fixed designation F1068;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification,to be used in conjunction withSpecification F1073,covers the principal dimensions and themechanical requirements for manufacturing steel and alumi-num individually dogged,airtight/gastight double doors forpersonnel access through bulkheads,complete with frames,intended to maintain the structural and the air and gas tightnessintegrity of the bulkheads.1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.3 The following precautionary caveat pertains only to theTest Methods portion,Section 6,of this specification:Thisstandard does not purport to address the safety concernsassociated with its use.It is the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2.Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA131/A131M Specification for Structural Steel for ShipsB209 Specification for Aluminum and Aluminum-AlloySheet and PlateF1073 Specification for Door Fittings,for Watertight/Gastight/Airtight,Weathertight,and Non-Tight Doors,for Marine Use2.2 ABS Standard:Rules for Building and Classing Steel Vessels32.3 Military Standards:MIL-R-900 Rubber Gasket Material,45 Durometer Hard-ness4MIL-C-81706 Coating,Aluminum and Aluminum Alloys4MIL-P-24441 Epoxy-Polyamide Paint4DoD-STD-2138 Metal Sprayed Coating System for Corro-sion Protection4TT-E-490 Enamel,Silicone Alkyd Copolymer,Semi-Gloss,Exterior4ZZ-R-765 Rubber,Silicone43.Ordering Information3.1 Ordering for doors under this specification shall includethe following:3.1.1 Material of doors,3.1.2 Nominal and ASTM designations,fixed lights or nolights,3.1.3 Quantity,and3.1.4 Location of active and inactive panels.3.2 Inspection and acceptance of doors shall be agreed uponbetween the purchaser and the supplier.4.Construction,Shape,and Dimensions4.1 The construction,shape,and clear opening dimensionsshall be as shown in Fig.1 and Table 1;in addition,they shallconform to the following requirements:4.1.1 Door frames shall be supplied as indicated in Fig.1.The corner radius inside of door frame shall be 8 in.(203 mm).4.1.2 Dogs shall be located on the door panels unlessotherwise specified.4.1.3 The doors shall be fitted with dogs,hinges,hasp andstaple assemblies,grab handles,label plates,and hook assem-blies.4.1.4 The position of the grab handles shall be located at thecenter of the height of each door panel.4.1.5 The components shall be attached to the steel doors.Components shall be attached to aluminum doors by eitherwelding or bolting.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Oct.1,2012.Published October 2012.Originallyapproved in 1987.Last previous edition approved in 2007 as F1068 90(2007).DOI:10.1520/F1068-90R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Bureau of Shipping(ABS),ABS Plaza,16855Northchase Dr.,Houston,TX 77060,http:/www.eagle.org.4Available from Standardization Documents,Order Desk,Bldg.4,Section D,700 Robbins Ave.,Philadelphia,PA 19111-5094,ATTN:NPODS.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.1.6 The material of standard door components shall be asgiven in Table 2.4.1.7 Welding shall be done in accordance with ABS Rulesfor Building and Classing Steel Vessels.5.Workmanship,Finish,and Appearance5.1 All sharp and ragged edges shall be ground flush andremoved for personnel protection.5.1.1 The door panels,upon completion,shall be straightwith a tolerance of 6116in.(1.6 mm).5.2 Pretreatment and priming of door components shall beas follows:5.2.1 Steel door and components,except component No.3,are to be coated with inorganic zinc rich primer,SSPC Paint 20Type I-C,at 1.5 to 3.0 mils(MDFT),both sides,beforeassembly,following surface preparation in accordance with themanufacturers instructions.5.2.2 Aluminum door and components,except componentNo.3,are to be pretreated with vinyl wash primer coating,followed with lead free,chromate free,anti-corrosion primeNOTE