ASTM_F_1510_-_07_2013.pdf

Designation:F151007(Reapproved 2013)An American National StandardStandard Specification forRotary Positive Displacement Pumps,Ships Use1This standard is issued under the fixed designation F1510;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification defines the requirements applicable todesign and construction of rotary positive displacement pumpsfor shipboard use.The classes of service are shown in Section4.1.2 This specification will not include pumps for hydraulicservice or cargo unloading applications.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2.Referenced Documents2.1 ASTM Standards:2A27/A27M Specification for Steel Castings,Carbon,forGeneral ApplicationA36/A36M Specification for Carbon Structural SteelA48/A48M Specification for Gray Iron CastingsA53/A53M Specification for Pipe,Steel,Black and Hot-Dipped,Zinc-Coated,Welded and SeamlessA159 Specification for Automotive Gray Iron CastingsA193/A193M Specification for Alloy-Steel and StainlessSteel Bolting for High Temperature or High PressureService and Other Special Purpose ApplicationsA194/A194M Specification for Carbon andAlloy Steel Nutsfor Bolts for High Pressure or High Temperature Service,or BothA322 Specification for Steel Bars,Alloy,Standard GradesA354 Specification for Quenched and Tempered Alloy SteelBolts,Studs,and Other Externally Threaded FastenersA395/A395M SpecificationforFerriticDuctileIronPressure-Retaining Castings for Use at Elevated Tempera-turesA434 Specification for Steel Bars,Alloy,Hot-Wrought orCold-Finished,Quenched and TemperedA449 Specification for Hex Cap Screws,Bolts and Studs,Steel,Heat Treated,120/105/90 ksi Minimum TensileStrength,General UseA515/A515M Specification for Pressure Vessel Plates,Car-bon Steel,for Intermediate-and Higher-Temperature Ser-viceA536 Specification for Ductile Iron CastingsA563 Specification for Carbon and Alloy Steel NutsA564/A564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and ShapesA574 Specification forAlloy Steel Socket-Head Cap ScrewsA582/A582M Specification for Free-Machining StainlessSteel BarsA743/A743M Specification for Castings,Iron-Chromium,Iron-Chromium-Nickel,Corrosion Resistant,for GeneralApplicationB150M Specification for Aluminum Bronze,Rod,Bar,andShapes Metric(Withdrawn 2002)3B584 Specification for Copper Alloy Sand Castings forGeneral ApplicationsD1418 PracticeforRubberandRubberLaticesNomenclatureD2000 Classification System for Rubber Products in Auto-motive ApplicationsD3951 Practice for Commercial PackagingF104 Classification System for Nonmetallic Gasket Materi-alsF912 Specification for Alloy Steel Socket Set ScrewsF1511 Specification for Mechanical Seals for ShipboardPump Applications2.2 ANSI Standard:4B 16.5 Pipe Flanges and Flanged Fittings2.3 SAE Standards:5AS 568A Aerospace Size Standard for O-Rings1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved Oct.1,2013.Published October 2013.Originallyapproved in 1994.Last previous edition approved in 2007 as F1510 07.DOI:10.1520/F1510-07R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.5Available from Society of Automotive Engineers(SAE),400 CommonwealthDr.,Warrendale,PA 15096-0001,http:/www.sae.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1Copyright by ASTM Intl(all rights reserved);J 429 Mechanical and Material Requirements for ExternallyThreaded Fasteners2.4 AMS Standard:53215 Acrylonitrile Butadiene(NBR)Rubber Aromatic FuelResistant 65-752.5 ABMA Standards:69 Load Ratings and Fatigue Life for Ball Bearings11 Load Ratings and Fatigue Life for Roller Bearings2.6 AGMA Standard:7390.03 Gear Classification,Materials and Measuring Meth-ods for Unassembled Gears2.7 API Standard:8676 Positive Displacement PumpsRotary2.8 Military Standards:9MIL-S-901MIL-STD-167MIL-STD-7403.Terminology3.1 Definitions:3.1.1 capacitythe quantity of fluid actually delivered perunit of time at the ra