ASTM_F_1298_-_90_2018.pdf

Designation:F129890(Reapproved 2018)An American National StandardStandard Specification forFlexible,Expansion-Type Ball Joints for MarineApplications1This standard is issued under the fixed designation F1298;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the design,manufacture,andtesting of ball joints utilized for accommodating thermalexpansion and contraction,or mechanical movement of apipeline carrying fluid.The ball joints are intended for use insystems operating above 0F(18C).1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The following precautionary caveat pertains only to thetest methods portion,Section 7,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2A395/A395M SpecificationforFerriticDuctileIronPressure-Retaining Castings for Use at Elevated Tempera-turesF722 Specification for Welded Joints for Shipboard PipingSystems2.2 ANSI Standard:3B 31.1 Power Piping2.3 American Society of Mechanical Engineers:4ASME Boiler and Pressure Vessel Code,Section VIII,Division 1 Pressure Vessels Section IX,Welding andBrazing Requirements3.Ordering Information3.1 Each purchase order or inquiry for ball joints to thisspecification shall include the following as applicable:3.1.1 Title,number,and latest revision of this specification,3.1.2 Manufacturers part number or ball-joint typeinformation,3.1.3 Materials for ball joint and seals,if other than to thisspecification,3.1.4 Service conditions,3.1.4.1 Minimum and maximum operating temperature(F),3.1.4.2 Maximum operating pressure(psig),3.1.5 Fluid media(internal),3.1.6 Atmosphere or media(external),3.1.7 ANSI pressure class,facing and drilling of flangedends,and pipe schedule or wall thickness of ends for weld endjoints,3.1.8 Special end connections as defined by the purchaser,3.1.9 Ball sphere or other special coatings,if required,3.1.10 Qualification test report,if required,3.1.11 Drawing requirements;for example,envelope draw-ing sufficiently detailed to describe the ball joint to be supplied,and3.1.12 Other tests to satisfy customer requirements.4.Materials and Manufacture4.1 All pressure retaining components shall be fabricatedfrom wrought or cast steel.Ductile iron complying withSpecification A395/A395M may be used for the ball jointretaining ring in services not above 350 psig(2.41 N/mm2)or1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved March 1,2018.Published April 2018.Originallyapproved in 1990.Last previous edition approved in 2012 as F1298 90(2012).DOI:10.1520/F1298-90R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.4Available from American Society of Mechanical Engineers(ASME),ASMEInternational Headquarters,Two Park Ave.,New York,NY 10016-5990,http:/www.asme.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 450F(232C).Steel shall comply with one of the materialslisted in Section VIII,Division 1,of the ASME Code,or ANSIB 31.1.4.2 Bolting material shall be in accordance with ANSIB 31.1.4.3 Ball spheres shall be coated in accordance with themanufacturers standard practice or as specified by the custom-ers specification(see 3.1.9).4.4 Corrosion shall be considered in the de